Power distribution, with purpose.
Bonding in switchgear is the deliberate electrical connection of conductive parts so they remain at a defined electrical potential relative to one another. It supports fault-current paths and reduces hazardous voltage differences, but it is not a substitute for system grounding or a neutral conductor.
What bonding means inside an assembly
A switchgear assembly contains conductive elements that may include metal enclosures, doors, barriers, structural frames, and equipment grounding conductors. Bonding connects applicable parts with conductors, metal-to-metal joints, or other engineered connections so electrical continuity is maintained across the assembly. The exact arrangement depends on the equipment design, construction, and applicable project requirements; the visible presence of two metal parts does not by itself prove that their connection is adequate.
The purpose is functional and protective. If a fault energizes an enclosure or another conductive part, a suitably designed bonding path helps carry fault current through the intended circuit so protective devices can respond. Bonding also limits differences in electrical potential between connected metal parts. Its effectiveness depends on the path as a whole, including joints, conductors, connection surfaces, and the relationship to the source and protective device.
Bonding, grounding, and neutral are different functions
Bonding establishes continuity among conductive parts. Grounding connects a system or equipment to earth, directly or through an engineered grounding arrangement, for purposes defined by the system design and applicable rules. The equipment grounding path is associated with bonding and fault protection, but “bonded” and “grounded” are not interchangeable descriptions. A metal enclosure can be bonded to the equipment grounding path without being treated as the system’s grounded conductor.
The neutral is a circuit conductor that carries current during normal operation in systems that use one. Its connection to ground or bonded metal is controlled by the system configuration and the location of the applicable bonding point. Treating the neutral and enclosure as the same function can create parallel current paths or obscure where a connection is intended. Specify neutral and grounding arrangements separately, including whether a neutral is required and where the system bonding connection is to be made.

Illustrative application: a switchboard with joined sections
Consider a hypothetical low-voltage switchboard shipped in multiple sections for connection at the site. The design must account for electrical continuity between sections and between relevant doors or other conductive parts and the assembly’s intended bonding path. The interface may depend on specified mechanical joints, bonding conductors, hardware, or a combination of design features. Shipping splits, field assembly, paint or coating at contact points, and later modifications are details that warrant review rather than assumptions.
For a project in Dallas–Fort Worth or elsewhere, the purchaser should identify the shipping and installation arrangement and provide the one-line diagram, system grounding method, section layout, and any project-specific grounding details. The manufacturer and responsible project professionals can then evaluate the intended interfaces against the assembly design and applicable requirements. This example is illustrative only; it does not establish a particular construction method or guarantee that a given arrangement is suitable.
A common misunderstanding and its consequences
A frequent misconception is that bolting two metal parts together automatically makes them adequately bonded. Mechanical attachment may contribute to continuity, but the connection’s electrical suitability depends on the design and conditions at the interface. Paint, corrosion, loose or unsuitable hardware, field alterations, and broken or omitted bonding conductors can affect continuity. Conversely, a dedicated conductor should not be assumed necessary at every joint without reviewing the equipment design and applicable requirements.
Another error is to use a neutral conductor as a convenient substitute for bonding. That confuses normal load-current function with protective fault-current function and may produce unintended current on conductive parts. Neither visual inspection alone nor a generic statement that equipment is “grounded” resolves these questions. Installation, inspection, testing, and maintenance should follow approved documentation and be performed by qualified personnel using applicable safety practices.
Ratings, drawings, and order documentation
Bonding is related to, but does not replace, the assembly’s short-circuit and protective-device design. A fault-current path must be considered in the context of the specified system, equipment ratings, protective devices, and applicable standards. System nominal voltage and equipment maximum rating are distinct values, and neither alone establishes the adequacy of a bonding arrangement. Required ratings, components, standards, and any U.S.-origin requirements must be confirmed for the specific order.
For a new custom-built assembly quote, provide the one-line diagram, nominal system voltage, available fault current or required short-circuit rating, neutral and grounding requirements, bus and section details, intended installation interfaces, and governing project specifications. Include any required drawings, submittals, or documentation for review. The manufacturer can evaluate the requested configuration and available components; UL 891 applies to low-voltage switchboards where applicable, not as a general listing for medium-voltage equipment. A particular assembly’s status and compliance must be verified rather than presumed.
Related terms to use precisely
Equipment grounding conductor refers to a conductor used as part of the equipment grounding and bonding path. Grounded conductor commonly refers to a system conductor connected to ground, often the neutral in applicable systems. Grounding electrode conductor connects a system or equipment grounding point to a grounding electrode system where required. These terms describe different roles, so drawings and specifications should use them deliberately.
When reviewing a switchgear submittal, trace the bonding path across the assembly and its intended interfaces, then confirm how it connects to the project’s grounding design. Ask whether field-installed connections are required, what details govern section joints and doors, and which drawings document the arrangement. Clear answers help distinguish an intentional engineered path from an assumption based solely on metal contact.
Specifications & planning
Review the details that matter for your application. Final specifications and availability should be confirmed for your project.
| Evaluation factor | What to confirm |
|---|---|
| System configuration | Nominal voltage, grounding method, and whether a neutral is required |
| Fault-current design | Available fault current or specified short-circuit rating and protective-device coordination basis |
| Assembly interfaces | Section splits, field connections, doors, and any project-specific bonding details |
| Documentation | Applicable standards, submittals, component requirements, and U.S.-origin requirements for the specific order |
