Power distribution, with purpose.
Main lugs only (MLO) describes switchgear or a switchboard arrangement with incoming terminals for the feeder conductors but no integral main circuit breaker or other main protective device. The equipment therefore depends on an upstream device to provide the specified overcurrent protection and to coordinate with the distribution system.
What “main lugs only” means
In an MLO assembly, incoming conductors terminate at line-side lugs or terminals, then connect to the assembly’s bus. The assembly may have branch circuit breakers or other outgoing devices, but it does not have a main breaker that disconnects and protects the entire assembly at its incoming point. “Main lugs” names the incoming connection arrangement; it does not mean the assembly is unprotected.
The protective device is located upstream, such as in a source switchboard, transformer secondary arrangement, or feeder panel. Its suitability depends on the actual system and applicable design requirements. An MLO specification should make the upstream device and its relationship to the assembly clear rather than treating the term as a complete protection description.
How upstream protection shapes the application
An MLO configuration can be appropriate when a properly selected upstream breaker or fuse already provides the required protection and means of disconnection for the downstream assembly. For example, a hypothetical facility distribution design might feed an MLO switchboard from a breaker in a separate upstream panel. The breaker’s rating, settings where applicable, and interrupting capability would need review alongside the downstream equipment and the available fault current.
This arrangement can avoid duplicating a main device, but it creates an interface that must be documented and checked. The upstream device must be suitable for the conductors and downstream equipment under the governing design, installation, and code requirements. Protection coordination, selective operation goals, grounding and bonding, feeder routing, and the means to isolate the assembly are all project-specific considerations—not automatic outcomes of choosing MLO.

The common misunderstanding: lugs are not protection
A frequent mistake is to assume that an MLO assembly contains a main breaker simply because it has a main incoming connection. Lugs provide a termination point; they do not sense an overload, interrupt a fault, or serve as an overcurrent protective device. Branch breakers protect their respective circuits, but they do not necessarily provide the required protection for the incoming feeder or the assembly bus.
Another mistaken assumption is that any upstream breaker will work. Its location, rating, trip characteristics, interrupting rating, and relationship to conductor and bus ratings must be evaluated for the actual installation. The available fault current at the equipment terminals also matters. A mismatch can affect equipment selection and the protection scheme, so the design team should resolve these details before an order is finalized.
Ratings and documents to confirm
A quote request should identify the system nominal voltage and phase, intended application, incoming conductor information, branch-device schedule, and the upstream protective device. Provide the available fault-current information at the proposed connection point, the required short-circuit rating, enclosure and environmental requirements, and any coordination or labeling criteria. Nominal system voltage and equipment voltage rating are related but distinct; the applicable ratings must be confirmed for the specific design.
Drawings and submittal documents should show where the upstream protection resides and identify the intended feeder and incoming connection arrangement. Confirm that the proposed terminals accommodate the specified conductors and that the equipment ratings, protective-device data, and documentation align with the project requirements. Standards, component availability, and any U.S.-origin requirements must also be confirmed for the specific order. UL 891 applies to low-voltage switchboards when applicable; it is not a general listing for medium-voltage or high-voltage switchgear, and no listing should be assumed without confirmation.
Choosing MLO versus an integral main
The practical comparison is not simply fewer components versus more components. MLO may suit a design with established upstream protection and an acceptable isolation arrangement. An integral main device may be preferred where local switching, a dedicated main protective function, or a particular operating arrangement is required. Space, coordination, maintainability, system layout, and project rules can influence the decision, while adding a main device may change dimensions, cost, and the protection study.
For a manufacturer quote, purchasers should share the one-line diagram or equivalent distribution description, upstream device details, load and branch schedule, required ratings, connection requirements, and applicable project specifications. A switchgear manufacturer can use that information to develop a new custom assembly and review the requested configuration; final suitability depends on engineering review and confirmed components. Shorter lead time may be a goal, not a guarantee. Dallas–Fort Worth purchasers and customers elsewhere should provide the same technical information so the proposed equipment can be evaluated against the actual installation.
Related terms in a distribution design
A main breaker is an integral protective and switching device at the main incoming point, while feeder protection is provided by a device supplying a downstream circuit or assembly. A service disconnect is a defined disconnecting function under applicable requirements; an MLO label alone does not establish that the equipment is suitable to serve as one. These terms describe different functions and should not be used interchangeably in specifications.
Short-circuit rating describes an equipment capability under stated conditions, whereas an upstream breaker’s interrupting rating describes that device’s ability to interrupt fault current. Coordination concerns how protective devices respond relative to one another. These concepts are related but not substitutes: a correct MLO design needs the complete protection scheme and equipment data, not just a selected lug size or a single headline rating.
Specifications & planning
Review the details that matter for your application. Final specifications and availability should be confirmed for your project.
| Evaluation factor | Information to confirm |
|---|---|
| Upstream protection | Device location, type, rating, and relevant settings |
| System and fault conditions | Nominal voltage, phase, and available fault current at the connection |
| Equipment interface | Incoming conductor details, lug requirements, and feeder arrangement |
| Documentation | Required short-circuit rating, applicable standards, and project-specific submittals |
