Power distribution, with purpose.
Mechanical and electrical interlocks both prevent incompatible switchgear operations, but they do so through different mechanisms and impose different design and maintenance demands. The right choice depends on the equipment’s operating states, the consequences of an incorrect operation, and how reliably the control system can establish those states. This guide outlines practical selection questions for new distribution equipment; final design, settings, work practices, and code interpretation belong to qualified professionals.
Start with the prohibited operating states
An interlock is meaningful only when the prohibited condition is explicit. In a two-source transfer arrangement, for example, the design may need to prevent both source breakers from being closed at once to avoid unintended paralleling. That rule is not automatic: some systems are designed for intentional closed-transition transfer, while others prohibit parallel operation. A bypass, tie breaker, generator connection, or alternate operating mode can change the required logic.
Define what each device state means before choosing an interlock. Closed, open, withdrawn, test, racked-in, control power available, and source healthy are distinct conditions. A breaker’s auxiliary contact may report its mechanism position without proving that a source is energized or acceptable. The sequence must specify which state is detected, which action is blocked, and what happens during transfer, maintenance, loss of control power, or restoration.
Mechanical interlocks: direct restraint, limited scope
A mechanical interlock uses a physical mechanism—such as a trapped key, linkage, or manufacturer-designed operating restraint—to make a prohibited sequence difficult or impossible at the equipment interface. Its useful feature is that the restraint does not depend on a PLC, network message, or electrical control supply to perform its basic blocking function. It can suit a clearly defined sequence between compatible devices when the mechanism and operating procedure are engineered together.
Mechanical arrangements have boundaries. A key exchange can enforce a sequence but may not independently verify electrical conditions such as voltage, phase, or source availability. Linkages and key schemes also require compatible equipment, correct installation, clear key control, and inspection for wear or damage. A design review should identify every permitted key, its controlled device, the expected sequence, and any defeat or bypass provision. Never treat a restraint as authorization to operate equipment outside approved procedures.

Electrical interlocks: logic depends on inputs
An electrical interlock uses control-circuit devices or programmed logic to permit or inhibit an operation. Inputs may include breaker auxiliary contacts, selector switches, voltage-sensing relays, protective-device status, or remote commands. Hardwired logic can use contacts and relays to create a defined permissive path; programmable controls can support more complex sequencing, alarms, and operator indications. In either case, the logic is only as dependable as its input definitions, wiring, power source, and documented behavior.
Specify signal ownership and failure response rather than writing only “electrically interlocked.” For each permissive, identify its source, normal state, contact type where relevant, and response to an open circuit, short circuit, loss of control power, or invalid signal. Communication interfaces add questions about message validity, timeout, stale data, network failure, and local control authority. A communications command should not be assumed equivalent to a hardwired safety-related permissive; the application and required risk controls need engineering review.
Gather the source data before selecting an approach
A useful design basis includes a one-line diagram, source and tie arrangement, operating modes, transfer sequence, and a list of operations that must be prevented or allowed. Provide nominal system voltage and the applicable equipment maximum rating as separate values, plus available fault-current information, breaker details, control voltages, and any required short-circuit ratings. Identify whether parallel operation is prohibited, permitted briefly, or intentionally continuous, and state what “source healthy” means for the project.
Also supply interface and documentation needs, including existing schematics, terminal conventions, PLC or supervisory-system protocols, remote/local operating requirements, environmental conditions, applicable standards, and project-specific U.S.-origin requirements. For a quote on new equipment, explain the intended sequence, equipment configuration, ratings, control interfaces, and required submittals. Ratings, component availability, standards, and origin requirements must be confirmed for the specific order; do not assume an existing drawing or a general product description settles them.
Hypothetical choice and competing options
Consider a hypothetical low-voltage lineup with two independent sources and a tie breaker, where the owner prohibits paralleling and wants either source to serve the load through the tie. The design team might compare a mechanical key sequence that prevents selected combinations of closed breakers with hardwired electrical permissives based on breaker status contacts. If remote transfer, source-quality checks, or detailed alarms are required, logic may add value, but it also introduces more signals and failure modes to define.
The decision is not simply mechanical versus electrical. A mechanical restraint may provide a local, control-power-independent barrier while electrical logic handles source qualification and annunciation. A combined approach can add layers, but it may also create conflicting indications, maintenance complexity, or an unsafe assumption that one layer compensates for an incomplete other layer. The team should test normal, abnormal, and maintenance states on paper, then determine through engineering review what arrangement meets the project’s risk and operating requirements.
Document behavior and define the conclusion’s limits
The design record should make the intended sequence reviewable by operators, maintainers, and commissioning personnel. Relevant records can include the one-line diagram, elementary control schematics, interconnection and terminal drawings, logic or cause-and-effect descriptions, key schedule, device and contact data, interface definitions, and a list of assumptions. Where programmable logic or communications are involved, document signal mapping, permissive conditions, timeout behavior, control authority, and the response to loss or disagreement of status.
A written decision should identify what the interlock does not prove and what conditions require a separate protection or operating measure. It is not a substitute for protective relaying, equipment ratings, isolation procedures, or qualified operating practice. New custom switchboards and related distribution equipment can be built to defined project requirements, with UL 891 applicable to low-voltage switchboard assemblies where appropriate; it does not apply as a general listing for medium-voltage gear. Final applicability and capabilities must be validated for the specific design. Dallas–Fort Worth purchasers and nationwide buyers should provide the same complete technical basis before equipment is quoted.
Specifications & planning
Review the details that matter for your application. Final specifications and availability should be confirmed for your project.
| Evaluation factor | Design question |
|---|---|
| Prohibited states | Which device combinations or sequences must be blocked? |
| State detection | What proves breaker position, source health, or control availability? |
| Failure behavior | What happens on loss of power, open wiring, invalid data, or network timeout? |
| Documentation | Which schematics, logic descriptions, interfaces, and operating records are required? |
