NEW AMERICAN-MADE POWER DISTRIBUTIONSERVING DALLAS – FORT WORTH
Gray electrical switchgear cabinets with breaker panels
NEW EQUIPMENT FOR DALLAS–FORT WORTH

EV Charging Facility Switchgear Load Planning

Plan EV charging facility switchgear around measured demand, charger behavior, protection coordination, utility interfaces, and future expansion.

MADE IN USAAmerican components
UL 891Switchboard assemblies
SHORT LEAD TIMESConfirm your project schedule
BUILT FOR YOUR PROJECT

Power distribution, with purpose.

EV charging switchgear planning starts with the facility’s electrical behavior, not the sum of charger nameplates alone. Charger count, simultaneous use, power-sharing controls, site growth, and utility limits all shape the distribution design. A sound basis of design records those inputs, tests how operating conditions may change, and identifies what must be confirmed by the engineer, utility, and equipment manufacturer before procurement.

Build the Load Model from Operating Data

Collect the charger schedule by model, quantity, input voltage, maximum input current or kVA, power factor, harmonic information, and manufacturer-stated operating limits. Separate the maximum connected load from the expected coincident demand. A managed site may allocate power across several ports, but the design should not assume that control system will always constrain load unless its function, failure behavior, and electrical interface are documented and accepted by the responsible engineer. Include charging behavior during startup, recovery after an outage, and high-use periods.

Add the rest of the facility: building loads, HVAC, lighting, maintenance equipment, and any planned additions. Record existing transformer and service data, interval demand where available, utility service constraints, and relevant operating schedules. For a Dallas–Fort Worth site, summer cooling demand may coincide with charging peaks, so an annual energy figure alone is a poor basis for sizing. Identify which inputs are measured, estimated, or pending; that distinction helps prevent a preliminary forecast from being mistaken for a design requirement.

Choose a Distribution Configuration for the Site

Compare a central distribution arrangement with more distributed charger feeders based on feeder lengths, equipment locations, voltage drop, maintainability, and expansion plans. A low-voltage switchboard may serve downstream distribution equipment, while a medium-voltage service can require a different equipment lineup and transformer interface. System nominal voltage and equipment maximum rating are separate specification values; the engineer must define both along with phase, frequency, neutral requirements, and grounding method. UL 891 applies to low-voltage switchboards, not medium-voltage switchgear.

Consider how the facility will isolate charger groups for maintenance or faults without unnecessarily interrupting unrelated loads. More feeder sections and distribution points can improve operational separation, but add equipment, space, connections, and coordination work. A centralized lineup may simplify service access and monitoring, while longer downstream runs can affect conductor sizing and fault-current performance. Draw the actual one-line architecture before requesting a firm equipment configuration, and verify that the selected topology fits the utility service, site layout, and charger vendor’s connection requirements.

Illustrative close-up of copper busbars in a motor control panel
Illustrative industry photograph · ToT89 / Wikimedia Commons · resized · CC BY-SA 4.0

Evaluate Demand Changes and Expansion Choices

Charging demand can shift as port utilization grows, fleet schedules change, or higher-power chargers replace earlier units. Model at least the initial operating case and a defined future case, stating charger quantities, diversity assumptions, and control limits for each. Also consider a loss of load management: if chargers revert to unrestricted operation, determine whether service, transformer, bus, and feeder loading remain within approved limits or whether an interlock or operating restriction is required. Such conclusions belong to the project’s qualified engineering team.

A practical hypothetical decision might compare installing full capacity for a planned second charger phase now against reserving lineup space and adding capacity later. The first choice may reduce future outage and retrofit work but commits capital and footprint before demand is certain. The second can defer investment, yet future additions may require new bus sections, protection changes, utility review, or shutdowns. “Spare space” alone does not establish that a lineup can accept a later load; reserve capacity, short-circuit duty, thermal limits, and control interfaces must be evaluated together.

Coordinate Protection, Controls, and Utility Interfaces

Protection design depends on available fault current, transformer impedance, conductor lengths, device characteristics, and the charger’s internal protection and fault response. Request utility fault-current information and transformer data, then coordinate the switchgear protective devices with downstream equipment and the facility’s selective-coordination requirements where applicable. Define the required interrupting and short-circuit ratings for the specific system. Do not infer an acceptable rating from nominal voltage or from a similar site; available fault current and applicable requirements must be confirmed for this order.

Document the boundary between switchgear, metering, energy management, charger controls, communications, and any emergency or demand-response functions. Clarify which party supplies control power, status points, trip or inhibit signals, network hardware, and programming. A communications command to reduce charging is not automatically equivalent to a protective device or a code-required disconnect. Final settings, protection studies, work practices, and code interpretation must be reviewed by qualified professionals and the authority having jurisdiction.

Prepare Drawings and Records Before Quoting

A useful quote package includes a one-line diagram, load schedule, charger cut sheets, service and transformer information, preliminary fault-current data, and the intended initial and future operating cases. Provide a site plan or equipment-room layout showing access, feeder directions, cable-entry preferences, and known space constraints. Include metering, communication, enclosure, environmental, and seismic requirements when applicable, along with any specified standards, project documents, or US-origin requirements. Unconfirmed items should be identified as open decisions rather than silently treated as settled.

Also provide the requested system voltage, continuous-load assumptions, bus and feeder requirements, protective-device preferences if established by the engineer, and the purchaser’s target delivery window. These details allow a manufacturer to evaluate a new custom build and identify information still needed; they do not substitute for engineering approval. The manufacturer builds and supplies new equipment, with American components and shorter lead time as a goal, not a guarantee. Component availability, ratings, standards, country-of-origin requirements, and any applicable assembly status must be confirmed for the specific order.

Keep the Design Conclusion Within Its Limits

A load-planning study supports equipment selection, but it does not by itself establish that a service can be obtained, that a utility will approve a load profile, or that every future charger will match today’s assumptions. Confirm utility requirements, charger submittals, code obligations, environmental conditions, and project specifications before releasing equipment. If the charger mix changes after design, revisit demand, feeder loading, fault duty, protective coordination, and the control strategy instead of relying on the original schedule.

Treat preliminary diagrams and calculations as design inputs until reviewed and issued by the responsible professionals. The switchgear manufacturer can use project documents to develop an equipment proposal, but final system design, settings, installation methods, commissioning, and operating procedures remain subject to qualified engineering and applicable authority review. The table below gives example evaluation factors only; values and acceptance criteria require project-specific engineering confirmation.

PROJECT CONSIDERATIONS

Specifications & planning

Review the details that matter for your application. Final specifications and availability should be confirmed for your project.

Emerging Loads: specifications and planning considerations
Evaluation factorProject-specific question
Load basisWhat coincident demand and control behavior are documented?
Future provisionWhich later loads and operating cases are included?
Fault dutyWhat utility and transformer data establish available fault current?
InterfacesWho defines metering, control signals, and charger coordination?
READY TO DISCUSS YOUR PROJECT?Let's build what's next.
Call (951) 403-5738
LET'S GET TO WORK

Power your next project
with confidence.

Talk through your switchgear and power distribution needs with our team.

Call (951) 403-5738
Request a Quote