NEW AMERICAN-MADE POWER DISTRIBUTIONSERVING DALLAS – FORT WORTH
Switchgear cabinets on pallets in an equipment warehouse
NEW EQUIPMENT FOR DALLAS–FORT WORTH

Harmonic Study Inputs for Nonlinear Loads

Learn which source, load, and equipment data a harmonic study needs, how assumptions shape results, and what engineers should review before design.

MADE IN USAAmerican components
UL 891Switchboard assemblies
SHORT LEAD TIMESConfirm your project schedule
BUILT FOR YOUR PROJECT

Power distribution, with purpose.

A harmonic study is only as useful as its model of the electrical source and the nonlinear loads that will operate on it. For a distribution design, the results can influence transformer selection, feeder and neutral sizing, power-factor correction, filtering, and switchboard requirements. Gather the data before equipment is specified: missing or generic inputs can make a model look precise while concealing the conditions that drive distortion or resonance.

Define the system boundary and study question

Start by identifying what the study must decide. A facility-wide assessment may examine voltage distortion at the service and sensitive buses, while a design comparison may focus on whether a proposed transformer or capacitor bank changes distortion at a particular point of common coupling. State the nominal system voltage, frequency, one-line topology, operating modes, utility point of connection, and the buses where results will be evaluated. Distinguish nominal voltage from the equipment’s maximum voltage rating; neither value alone describes the harmonic behavior of the system.

The boundary matters because the upstream source is part of the circuit. Obtain utility fault-current or Thevenin-equivalent data at the point of connection, including X/R ratio and any available frequency-dependent impedance information. Ask whether the data represent a minimum or maximum source condition and what network configuration they assume. If a utility value is unavailable, the engineer should document a defensible assumption and test its effect rather than treat an estimate as a measured fact.

Collect load spectra, operating profiles, and nameplate details

For each significant nonlinear load, provide manufacturer and model information, input topology, rated kW or kVA, voltage, phase, and expected operating range. Request harmonic current spectra by order, with the basis clearly stated: percent of fundamental current, amperes, or another defined reference. Include power factor, displacement power factor where available, and whether the data describe typical, maximum, or specified operating conditions. Variable-frequency drives, UPS systems, rectifiers, EV charging equipment, and electronic lighting can have materially different spectra even when their kVA values are similar.

The model also needs a credible picture of how loads run together. Supply schedules showing quantity, diversity or duty assumptions, expected loading, start-up or standby modes, and future expansion that is actually part of the design basis. Record existing capacitor banks, filters, generators, transformers, and large motors, including ratings and connection details. For a Dallas–Fort Worth facility or a project shipping elsewhere, the same principle applies: local weather or location does not replace equipment-specific spectra and the utility’s source data.

Illustrative close-up of copper busbars in a motor control panel
Illustrative industry photograph · ToT89 / Wikimedia Commons · resized · CC BY-SA 4.0

Make assumptions visible and test competing designs

A study model should identify what is measured, what comes from vendor data, and what is assumed. Important choices include transformer impedance and winding connection, cable lengths and conductor sizes, motor representation, load aggregation, background voltage distortion, and the treatment of utility impedance by harmonic frequency. Explain whether loads are modeled as current sources and how phase-angle diversity or cancellation is represented. A single idealized spectrum applied to every converter may overstate or understate coincident distortion.

Compare alternatives against the same source and operating cases. A hypothetical decision might compare a standard six-pulse drive arrangement with a lower-harmonic option, then test whether a capacitor bank introduces a resonance near a strong harmonic. The comparison should consider distortion, losses, voltage regulation, available fault current, footprint, controls, maintenance, and interactions with generators or other operating modes. The example is illustrative, not a prediction for a particular facility; an engineer must verify inputs and determine which limits and criteria govern.

Read outputs as engineering evidence, not a pass label

Useful deliverables typically identify the modeled cases and report voltage and current distortion at specified buses, individual harmonic orders, and relevant compliance or design criteria. They may include frequency scans, impedance plots, resonance findings, equipment loading, and comparisons of proposed mitigation. Ask for the point of evaluation and the denominator used for each distortion metric; total harmonic distortion and total demand distortion are not interchangeable, and a result without its measurement location or operating case can be misleading.

A favorable result does not establish that every operating state is acceptable. Review worst-case utility strength, lightly loaded and heavily loaded conditions, capacitor switching, generator operation, and planned expansions when relevant. Harmonic limits and code or utility requirements depend on the project and point of application. The responsible engineer should interpret the applicable standards, document exclusions and uncertainty, and decide whether measurements after commissioning are needed to validate the model.

Provide records that connect the study to equipment design

A useful study package includes the current one-line diagram, load schedule, panel and feeder information, transformer data, utility source letter or equivalent, equipment submittals, and available field measurements. Include revisions and mark uncertain or preliminary values. The engineer can then trace a result back to a specific bus, feeder, load, and operating assumption instead of relying on an unverified summary. When equipment changes after the study, the model should be reviewed for impacts rather than presumed valid.

When requesting a new switchboard or related distribution equipment quote, provide the study’s applicable one-line, bus and feeder requirements, system voltage and frequency, main and branch device information, enclosure and environmental requirements, and any required short-circuit or coordination constraints. Identify harmonic mitigation components and their interfaces if they are part of the design. A manufacturer can build to confirmed project specifications, but the purchaser and engineer must verify ratings, component availability, standards, and any U.S.-origin requirements for the specific order. UL 891 applies to low-voltage switchboards where applicable, not medium-voltage equipment.

Set boundaries for conclusions and next steps

A harmonic study evaluates the modeled network and stated conditions; it does not guarantee future load behavior, utility conditions, or equipment performance outside those assumptions. Vendor spectra may change with firmware, loading, or product selection, and measured data can differ from catalog values. Treat the report as a design input with a stated date, revision, model boundary, source-data quality, and list of unresolved items. Re-run or update it when a material load, transformer, capacitor, or source configuration changes.

Final equipment selection, protection settings, work practices, and code interpretation belong to qualified electrical professionals familiar with the project and governing requirements. Do not use a study summary alone to authorize field changes or energized work. Clear handoff between the study engineer, equipment purchaser, and manufacturer helps preserve the assumptions through procurement and submittal review, while leaving the responsible engineer in control of the technical conclusion.

PROJECT CONSIDERATIONS

Specifications & planning

Review the details that matter for your application. Final specifications and availability should be confirmed for your project.

Engineering Studies: specifications and planning considerations
Evaluation factorInformation to confirm
Utility sourceShort-circuit strength, X/R, and modeled source conditions
Nonlinear loadsVendor spectra, operating range, and concurrent duty
Network modelOne-line topology, transformer data, cables, and capacitors
Study resultEvaluation bus, harmonic metric, operating case, and governing criteria
READY TO DISCUSS YOUR PROJECT?Let's build what's next.
Call (951) 403-5738
LET'S GET TO WORK

Power your next project
with confidence.

Talk through your switchgear and power distribution needs with our team.

Call (951) 403-5738
Request a Quote