NEW AMERICAN-MADE POWER DISTRIBUTIONSERVING DALLAS – FORT WORTH
Switchgear cabinets arranged on a warehouse floor
NEW EQUIPMENT FOR DALLAS–FORT WORTH

Energy Metering for Multiple Tenants

Plan tenant energy metering by defining measurement points, CT and VT inputs, accuracy needs, data ownership, drawings, and billing interfaces.

MADE IN USAAmerican components
UL 891Switchboard assemblies
SHORT LEAD TIMESConfirm your project schedule
BUILT FOR YOUR PROJECT

Power distribution, with purpose.

Energy metering for multiple tenants is a distribution-design decision, not simply a choice of meter. The design must establish which loads belong to each tenant, where those loads connect, how current and voltage reach the meters, and who can access the resulting data. Those choices affect billing, energy reporting, troubleshooting, and future tenant changes. A switchboard or distribution assembly can be configured around a documented metering plan, but final device selection, settings, work practices, and code interpretation belong with qualified electrical professionals.

Define the boundary of each tenant’s measurement

Begin with a one-line diagram and a load schedule that identify the service entrance, house loads, tenant feeders, and any shared equipment. The central question is the measurement boundary: does each meter measure only one tenant’s feeder, or does it also include branch circuits, dedicated common-area loads, or equipment serving more than one space? A meter at a tenant feeder can simplify allocation, but it may not capture downstream loads supplied from a shared panel or account for losses and common services. Those items need an explicit allocation method rather than an assumption that the meter totals equal the utility bill.

Record the electrical characteristics at each proposed point, including system configuration, nominal voltage, phase, frequency, feeder arrangement, expected load range, and available fault-current information. Distinguish the system’s nominal voltage from the meter input rating and any equipment maximum rating. For a Dallas–Fort Worth commercial property, as elsewhere, local utility service details and the project’s adopted requirements must be confirmed for the specific site; a regional location alone does not establish a standard service configuration.

Match measurement inputs to the circuit

The meter needs voltage inputs and current inputs appropriate to the circuit it observes. Direct voltage connections may be suitable for some low-voltage applications, while other designs use voltage transformers (VTs), also called potential transformers, to provide an instrument-level signal. Current transformers (CTs) provide a corresponding current signal. Selection depends on the system voltage and connection, meter input limits, conductor arrangement, expected current, and the instrument’s specified input requirements. A three-phase circuit’s wiring configuration also determines which voltage and current relationships the meter uses to calculate energy.

CT ratio should reflect credible operating current, not merely the feeder’s maximum rating. An oversized ratio can reduce useful resolution at ordinary tenant loads; an undersized ratio can exceed the CT or meter input capability during expected operation. The design must also specify CT accuracy class, burden, polarity, ratio, and placement, along with VT ratio, accuracy, burden, and protection where applicable. Confirm that meter and transformer combinations are compatible and that the assembly layout provides the intended measurement point. These decisions require engineering review; this guide does not prescribe field installation or energized work.

Illustrative close-up of copper busbars in a motor control panel
Illustrative industry photograph · ToT89 / Wikimedia Commons · resized · CC BY-SA 4.0

Set accuracy and data expectations before selecting equipment

“Accuracy” should be tied to the purpose of the reading. Internal energy allocation, tenant information displays, operational trending, and formal revenue billing can carry different requirements. Specify the required measurement performance across the expected load range, the relevant meter and CT/VT accuracy, and how the complete measurement chain will be evaluated. A meter’s stated accuracy alone does not establish the accuracy of a system that includes transformers, wiring, configuration, and installation. If readings will support charges, the owner should confirm applicable legal, utility, contractual, and metrology requirements with the appropriate professionals.

Decide who owns and administers the data before selecting communication interfaces. The owner may retain records while tenants receive limited access, or a property platform may collect interval data from multiple meters. Document meter identifiers, time synchronization, interval length, units, register definitions, communications protocol, network responsibility, and retention expectations. Also clarify whether data must be exportable for billing or energy-management software and who handles access credentials and tenant turnover. Communications compatibility is a project interface to verify, not an assumption based on a meter’s display or protocol label.

Use a worked decision to expose tradeoffs

Consider a hypothetical building with four tenant feeders, one house-services panel, and a shared pump supplied from a common distribution point. The design team first maps each feeder and identifies whether the pump is a landlord expense or a shared tenant cost. If it is landlord-funded, the team can meter the four tenant feeders separately and keep house services and the pump on a distinct measurement channel. If the pump cost is allocated, its meter boundary and allocation rule must be documented; adding its energy informally to tenant totals would make the readings difficult to audit.

For this example, the team compares meters at the main switchboard with meters in downstream tenant panels. Main-board metering can centralize access and may make feeder totals easier to associate with the distribution assembly, but it can require longer measurement wiring and careful allowance for feeder routing and CT placement. Downstream metering can align readings more closely with tenant panels, while increasing the number of locations, communications endpoints, and coordination points. The preferred choice follows the actual feeder layout, access strategy, accuracy objective, and maintenance plan—not a universal rule.

Provide a coordinated package for design and quotation

A useful quote request includes the current one-line diagram, panel schedules, service and feeder data, anticipated load information, tenant count, proposed meter locations, and the intended allocation boundary for common loads. Include the desired measurement purpose, required accuracy or billing criteria, CT and VT expectations if already engineered, communications protocol, monitoring platform interface, enclosure and environmental conditions, and any required utility or owner specifications. Identify whether meters are expected in a new switchboard, separate panels, or another assembly so the manufacturer can assess the requested configuration and interfaces.

For a new custom assembly, the manufacturer can review the stated metering provisions alongside the equipment scope and component requirements. Share applicable drawings, project specifications, and required standards or U.S.-origin provisions for confirmation. UL 891 may apply to a low-voltage switchboard when the specific assembly and project requirements support it; it is not a general designation for medium-voltage switchgear. Ratings, short-circuit capability, component availability, standards compliance, and origin requirements must be confirmed for the particular order. Shorter lead time may be a goal, but timing depends on the finalized design and confirmed components.

Keep records that make readings defensible

The design record should show meter tags and locations, the circuits included in each measurement, CT and VT ratios and polarity, wiring diagrams, meter input configuration, communications connections, and the relationship between readings and tenant accounts. Preserve approved submittals, equipment schedules, final drawings, commissioning or verification records where required, and the method used to allocate shared energy. Without those records, a replacement meter or tenant reconfiguration can silently change what a reading represents even when the displayed value appears plausible.

The conclusion remains limited by the information available at design time. Actual tenant loads, utility rules, service configuration, local code interpretation, metering regulations, software capabilities, and future occupancy can alter the right design. Qualified professionals should verify final ratings and settings, review protection and instrument-transformer details, and determine safe work practices. Treat the example as a decision framework, not an engineered design or promise that a particular meter arrangement will meet every billing or regulatory requirement.

PROJECT CONSIDERATIONS

Specifications & planning

Review the details that matter for your application. Final specifications and availability should be confirmed for your project.

Metering: specifications and planning considerations
Evaluation factorWhat to define
Measurement boundaryTenant feeder, shared loads, and house services included
CT/VT selectionCircuit configuration, expected load, ratio, accuracy, and burden
Data interfaceProtocol, interval data, access roles, and retention
Billing purposeInternal allocation versus requirements confirmed for formal billing
READY TO DISCUSS YOUR PROJECT?Let's build what's next.
Call (951) 403-5738
LET'S GET TO WORK

Power your next project
with confidence.

Talk through your switchgear and power distribution needs with our team.

Call (951) 403-5738
Request a Quote