NEW AMERICAN-MADE POWER DISTRIBUTIONSERVING DALLAS – FORT WORTH
Electrical equipment on a flatbed truck for transportation
NEW EQUIPMENT FOR DALLAS–FORT WORTH

Revenue Metering Versus Facility Metering

Compare revenue and facility metering inputs, accuracy, ownership, CT/VT selection, records, and tradeoffs for a specific distribution design.

MADE IN USAAmerican components
UL 891Switchboard assemblies
SHORT LEAD TIMESConfirm your project schedule
BUILT FOR YOUR PROJECT

Power distribution, with purpose.

Revenue metering and facility metering may use similar instruments, but they serve different decisions. One supports a utility’s billing or settlement process; the other helps an owner understand how electricity moves through a facility. The distinction affects measurement location, instrument-transformer specifications, data responsibility, and the records needed to approve a switchboard or other distribution assembly.

Define the measurement purpose and boundary

Start by identifying which quantity must be measured, at what electrical boundary, and who will rely on the result. Revenue metering is used to determine charges or settle energy transactions under the applicable utility, market, or contractual rules. Facility metering supports operational uses such as tracking building consumption, comparing feeders, or allocating energy among tenants. A meter that is adequate for internal trending may not meet the acceptance, sealing, testing, or accuracy requirements for billing.

The physical location matters as much as the meter type. A meter at the service point may record utility-supplied energy, while a downstream meter records only the loads beyond its current transformers (CTs) and voltage transformers (VTs). Determine whether the design must capture imports, exports, demand, power quality, or separate sources such as generators and energy storage. Confirm the measurement boundary with the utility and the owner’s electrical and metering professionals before fixing the one-line.

Specify measurement inputs and CT/VT selection

A meter needs appropriate current and voltage inputs for the circuit it monitors. CT ratio and rating should suit the expected load range and fault-duty design, while CT accuracy and burden must be appropriate to the intended use. A ratio selected only for maximum service capacity can reduce useful resolution at normal operating load; a ratio selected too tightly can be unsuitable for future load or operating conditions. Protection CTs and metering CTs also have different purposes and should not be treated as interchangeable without engineering review.

VTs, where required, provide voltage inputs at the meter’s specified levels and connection arrangement. The design must address system voltage, phase configuration, grounding, fusing, wiring burden, and whether the meter accepts direct voltage inputs or requires instrument transformers. Verify the system’s nominal voltage separately from the equipment’s maximum rating. Ratios, accuracy classes, burdens, wiring diagrams, and component availability must be confirmed for the specific order and approved measurement scheme.

Illustrative close-up of copper busbars in a motor control panel
Illustrative industry photograph · ToT89 / Wikimedia Commons · resized · CC BY-SA 4.0

Separate accuracy, acceptance, and data ownership

Accuracy is not a single meter specification. The complete measurement chain includes the meter, CTs, VTs, wiring, installation conditions, and applicable testing or calibration process. For revenue use, the governing utility or settlement requirements may define acceptable equipment, seals, access, test documentation, and who may alter the circuit. For facility monitoring, the owner may instead set accuracy needs around energy allocation, alarms, or comparison with utility bills. A published meter accuracy figure alone does not establish system-level performance.

Establish who owns the meter, instrument transformers, communications hardware, and resulting data. Clarify who can access readings, retain interval records, resolve discrepancies, and authorize changes. Revenue data may be governed by utility procedures or contracts, while facility data may flow to an owner’s building-management or energy platform. Confirm communications protocols, pulse or network interfaces, time synchronization, cybersecurity expectations, and responsibility for ongoing data service; these interfaces can affect panel space and wiring even when they do not change the power circuit.

Use source data to compare design options

A practical review begins with the utility service requirements, current single-line diagram, service voltage and phase, available fault-current information, load schedule, operating profile, and the owner’s monitoring objectives. Add the utility’s metering standard or written direction, proposed meter and communications requirements, CT/VT data, and any applicable tariff or tenant-allocation rules. For a replacement or expansion, identify existing metering locations and whether equipment must remain compatible with installed instruments or data systems.

Consider a hypothetical 480 V, three-phase facility service with a utility-designated billing meter at the service boundary and an owner seeking separate records for two production areas. One option is utility revenue metering at the boundary plus downstream facility meters on each area feeder. Another is a single revenue meter with facility submeters only where operational detail is needed. A third is to rely on the revenue data alone, which reduces added equipment but may not distinguish the production loads. The right choice depends on utility approval, load priorities, cost, and how readings will be used; this example is not a project specification.

Coordinate drawings, records, and assembly interfaces

Before equipment is quoted, provide the one-line diagram, service and feeder ratings, metering points, CT/VT ratios and accuracy requirements if established, meter models or functional requirements, and utility documents governing revenue measurement. Include control schematics, terminal plans, communications interface details, enclosure and compartment preferences, and the required short-circuit rating. Mark which components or circuits are utility-owned, utility-controlled, or owner-maintained, and identify any sealable barriers or access restrictions required by the utility.

The manufacturer needs enough information to define the assembly interface, not to decide the utility’s billing rules or substitute for the engineer of record. Identify the project location and delivery needs, requested schedule, applicable standards, and any US-origin or component constraints so they can be reviewed for the order. Custom new switchboard assemblies may be developed around documented requirements, with shorter lead time a goal rather than a guarantee. UL 891 applies to low-voltage switchboards where applicable; confirm the specific assembly’s requirements and status rather than assuming a listing.

Keep the decision within its limits

Metering requirements can change with utility territory, rate structure, service arrangement, ownership boundary, and the authority having jurisdiction. A diagram that appears to place a meter at the service entrance does not establish that the utility accepts its location or instrument transformers. Likewise, a facility submeter does not automatically provide a basis for tenant billing or regulatory settlement. Confirm the intended use and acceptance criteria with the parties responsible for them before release for manufacture.

The comparison here is a design framework, not a final meter schedule, code interpretation, or energized-work procedure. Qualified electrical engineers and metering professionals should verify calculations, equipment ratings, CT/VT application, protection coordination, drawings, settings, and applicable codes. In Dallas–Fort Worth or elsewhere, local utility requirements still need project-specific confirmation. Ratings, standards, component availability, and US-origin requirements must be checked for each order.

PROJECT CONSIDERATIONS

Specifications & planning

Review the details that matter for your application. Final specifications and availability should be confirmed for your project.

Metering: specifications and planning considerations
Evaluation factorRevenue metering
Primary purposeBilling or settlement under governing requirements
Measurement boundaryUtility or contractual point of measurement
Accuracy and acceptanceConfirm utility or settlement criteria
Data responsibilityConfirm ownership, access, and retention rules
READY TO DISCUSS YOUR PROJECT?Let's build what's next.
Call (951) 403-5738
LET'S GET TO WORK

Power your next project
with confidence.

Talk through your switchgear and power distribution needs with our team.

Call (951) 403-5738
Request a Quote