Power distribution, with purpose.
Instantaneous and short-time trip functions both respond to high current, but they differ in intentional delay and in how they affect coordination with downstream protective devices. Choosing between them is not a matter of selecting the faster setting by default: the decision depends on the one-line design, fault-current study, equipment withstand ratings, and the protection objectives for each section of the distribution system. This guide outlines how to evaluate that choice and what to provide when specifying new switchgear or switchboards.
How the Two Functions Respond
An instantaneous function trips when measured current exceeds its pickup threshold, without an intentional time delay. The breaker still has a finite operating and clearing time, but the relay or trip unit does not wait for a separate coordination interval. This can limit fault duration for a sufficiently high-current event. It may also trip a main device for a fault that a downstream breaker could otherwise clear, depending on pickup values, device characteristics, and the current seen by each device.
A short-time function also responds above a defined pickup, but adds a delay to allow a downstream protective device time to operate first. The delay may be a fixed-time or inverse-time characteristic, depending on the specific trip unit. That interval can improve selectivity, but it permits fault current to persist longer if the downstream device does not clear the fault. Neither function is inherently preferable; each must be assessed against the system’s protection, continuity, and equipment-damage objectives.
Start With System and Device Data
A useful evaluation begins with the current and voltage conditions at each protective device, not just the service entrance rating. The design team needs the utility source information, transformer ratings and impedance, conductor lengths and sizes, grounding method, motor contribution where applicable, and the operating configurations that change available fault current. A short-circuit study should identify the maximum and minimum fault-current conditions relevant to pickup, equipment duty, and protective-device operation.
Device-specific information matters as much as system data. Obtain breaker and trip-unit models, sensor or rating-plug details, current-time curves, interrupting and withstand data, and any manufacturer limits on adjustable settings. Confirm whether the proposed equipment supports the required functions and adjustment ranges. System nominal voltage and equipment maximum rating are distinct specifications; likewise, a current setting or coordination conclusion cannot be assumed from a nominal ampere rating alone.

A Hypothetical Coordination Decision
Consider a hypothetical low-voltage lineup with a main breaker feeding a distribution section and downstream feeder breakers. If a feeder fault produces current above both the feeder and main instantaneous pickups, both devices may begin tripping without a useful separation in response. Raising or disabling the main instantaneous function could improve selectivity in that operating region, but only if other protection remains adequate and the main breaker and assembly can withstand the resulting fault exposure.
A short-time pickup and delay might instead let the feeder breaker clear first, provided its curve and clearing time coordinate with the main’s short-time response. The engineer must check the full range of fault current, including lower current faults that may fall below one device’s instantaneous pickup, as well as the delay’s effect on thermal and mechanical duty. This example illustrates a decision method, not a recommended setting or evidence of any completed customer design.
Settings Ownership and Design Interfaces
Protection settings should have a clearly assigned technical owner. The engineer responsible for the system study typically establishes the coordination objectives and documents recommended values; the equipment supplier confirms device capabilities and configuration constraints. The purchaser or facility’s designated electrical authority should identify who reviews, approves, and records final settings. A manufacturer can build to an approved specification, but should not be treated as the substitute for project-specific engineering judgment.
The settings review must account for interfaces beyond the main and feeder breakers. Tie breakers, alternate sources, generator operation, transformer protection, ground-fault functions, and maintenance or operating modes can change which devices see a fault and which should trip. If settings are changed during commissioning or later operation, the approved study and records need updating. Qualified professionals must determine safe work practices and interpret applicable codes and standards for the actual installation.
Drawings and Records to Provide
For a new-equipment quote, provide the one-line diagram, system voltage and frequency, bus and feeder requirements, source and transformer data, available fault-current information, and the latest short-circuit and coordination studies if available. Include the intended protective-device lineup, breaker types or specifications, control and metering requirements, and any required operating modes. Identify the function and location of each main, tie, and feeder so the equipment scope can be checked against the design.
Useful records also include current-time curves, approved setting schedules, equipment schedules, grounding details, and any project-specific requirements for documentation or submittals. Mark assumptions and unresolved data explicitly rather than presenting estimates as confirmed values. The manufacturer builds and supplies new equipment, including custom configurations; component availability, ratings, applicable standards, and any U.S.-origin requirements must be confirmed for the specific order. Shorter lead time may be a goal, not a guaranteed delivery date.
Limits of the Conclusion
A written comparison of instantaneous and short-time functions cannot establish final settings without verified study inputs and the exact devices being evaluated. Changes in utility contribution, transformer impedance, conductor routing, breaker model, or system configuration can alter fault levels and coordination. Settings that appear selective on one curve may fail to coordinate at another current, or may exceed an equipment withstand limit during the intentional delay.
For projects in Dallas–Fort Worth or elsewhere, confirm the design basis and delivery requirements for the actual installation rather than assuming a regional standard configuration. Review proposed low-voltage switchboard construction and applicable UL 891 requirements where relevant; UL 891 does not apply as a general listing for medium-voltage switchgear. Final settings, work practices, standards interpretation, and code compliance should be determined by qualified professionals using project-specific information.
Specifications & planning
Review the details that matter for your application. Final specifications and availability should be confirmed for your project.
| Evaluation factor | What to verify |
|---|---|
| Fault-current range | Maximum and minimum values at each protective device |
| Device response | Trip-unit functions, pickup ranges, and time-current curves |
| Coordination objective | Which downstream devices should clear first, and under what conditions |
| Equipment duty | Interrupting, withstand, and allowable delay limits; engineering review required |
