NEW AMERICAN-MADE POWER DISTRIBUTIONSERVING DALLAS – FORT WORTH
Close-up view of switchgear cabinets on pallets
NEW EQUIPMENT FOR DALLAS–FORT WORTH

Distribution Switchboards

Understand distribution switchboard layouts, feeder breaker schedules, growth provisions, and the project data needed to specify new equipment.

MADE IN USAAmerican components
UL 891Switchboard assemblies
SHORT LEAD TIMESConfirm your project schedule
BUILT FOR YOUR PROJECT

Power distribution, with purpose.

A distribution switchboard receives power from an upstream source and divides it among downstream circuits, making it a central point for organizing and protecting a facility’s electrical distribution. Its practical value depends on more than the main rating: feeder arrangement, protective-device coordination, available space, and the planned path for future loads all shape the design. This guide explains the decisions to resolve before specifying a new switchboard.

How a switchboard fits into the distribution system

A typical arrangement brings power from a transformer, generator, or other source to a main device, then routes it through bus to feeder devices serving panels, motor loads, HVAC equipment, or other distribution points. Some systems use a main breaker; others use a main fused switch or a main-lugs-only arrangement where the upstream equipment provides the intended overcurrent protection. The appropriate topology depends on the one-line diagram, protection scheme, operating practices, and applicable requirements—not simply on the building’s size.

Do not treat nominal system voltage as the equipment’s maximum rating. The specification should identify the system voltage and frequency, grounding method, number of phases and wires, and required equipment voltage rating. It should also state the available fault current at the switchboard and the required short-circuit rating. These values affect device selection and system coordination, and must be confirmed for the actual installation.

Arrange feeders around real loads and operating needs

A feeder schedule turns the one-line concept into a usable layout. For each circuit, identify its destination, connected load or calculated demand, voltage, phase, conductor information when known, and required protective-device type and rating. Note special loads such as motors, transformers, welders, or electronic equipment because inrush, harmonics, and operating duty can affect breaker selection and coordination. A schedule that says only “spare” or “future” may leave important design questions unresolved.

Physical arrangement matters alongside electrical sizing. Grouping feeders by destination or function can make circuit identification and maintenance planning clearer, while the selected section layout must accommodate the devices, bus connections, wire-bending space, and cable entry direction. Confirm whether conductors enter from the top or bottom, where the incoming service or source terminates, and how the switchboard interfaces with adjacent equipment. These details can constrain the lineup even when the electrical ratings appear straightforward.

Illustrative close-up of copper busbars in a motor control panel
Illustrative industry photograph · ToT89 / Wikimedia Commons · resized · CC BY-SA 4.0

Make the breaker schedule coordinated and unambiguous

A useful breaker schedule identifies each device’s frame and trip requirements, poles, interrupting capability, adjustable functions if needed, and any accessories or control interfaces. The designer should check that the selected device’s interrupting rating is suitable for the available fault current at its location. Upstream and downstream protective devices also need review for coordination objectives; a switchboard quote cannot substitute for a complete protection study or resolve undocumented system conditions.

Consistency between the schedule, one-line diagram, and equipment specifications reduces ambiguity. Call out which circuits are essential, which may be shed, and whether any feeders require metering, ground-fault protection, shunt trip, or remote indication. Requirements vary with the application and governing codes. Confirm the project’s applicable standards, authority requirements, and any owner specifications during engineering review rather than assuming a particular configuration is universally compliant.

Plan growth without overbuilding the lineup

Future capacity can mean different things: unused breaker positions, bus capacity for later loads, physical space for another section, or a planned way to connect an additional source. Those provisions are not interchangeable. An empty position does not by itself establish that the bus, enclosure, or upstream supply can support future demand. Define the likely load additions, expected timing, and whether the future work must occur without replacing the original assembly.

Growth planning also involves a cost and footprint tradeoff. A larger lineup may preserve options but consume valuable electrical-room space and require more material now; a compact arrangement can be efficient but may make later expansion difficult. Ask the engineer to distinguish installed spare capacity from future expansion provisions and to document any assumptions about load, fault current, and available space. A future addition must be rechecked against the system and the equipment’s confirmed ratings.

Specify interfaces, enclosure, and installation constraints

The room and connection details influence the design as much as the circuit count. Provide the available footprint, access and working-space constraints, mounting conditions, environmental exposure, and any enclosure requirements. Identify whether the switchboard connects to busway, conduit, transformer terminals, generator equipment, or another lineup, and share the interface dimensions or connection requirements when available. Confirm shipping and handling limits with the project team; a design that fits electrically may still present access or placement challenges.

Metering, communications, and control needs should be defined before the arrangement is finalized. Specify whether the project needs local measurements, remote monitoring, communication protocols, or integration with existing controls, and identify who supplies related wiring and devices. For projects in Dallas–Fort Worth or elsewhere, site conditions and delivery coordination remain project-specific; serving a region does not establish a local manufacturing location. Installation, connection, and commissioning responsibilities should be assigned separately and confirmed with the responsible parties.

Prepare a quote package that supports engineering review

For a useful quote request, provide the current one-line diagram, feeder schedule, system voltage and grounding information, available fault-current data, required short-circuit rating, and the applicable project specifications. Include load information, source and downstream interfaces, enclosure and room constraints, metering or control requirements, and desired growth provisions. Identify the project location and schedule needs, while treating any requested lead time as a goal subject to design review, component availability, and order-specific confirmation.

The manufacturer builds new equipment and can evaluate custom configurations using American components where specified; actual component availability and U.S.-origin requirements must be confirmed for the order. UL 891 applies to low-voltage switchboards when the particular assembly and configuration meet applicable requirements; it is not a general rating for medium-voltage switchgear. All ratings, standards, listing status, and design details require confirmation for the specific order. A complete submittal review is the point to reconcile requirements before manufacturing.

PROJECT CONSIDERATIONS

Specifications & planning

Review the details that matter for your application. Final specifications and availability should be confirmed for your project.

Distribution Switchboards: specifications and planning considerations
Evaluation factorInformation to confirm
System basisNominal voltage, frequency, phases, wires, and grounding method
Fault dutyAvailable fault current and required equipment short-circuit rating
Feeder scheduleDestinations, load data, device requirements, and special functions
Growth planSpare positions, bus capacity, future sections, and documented assumptions
READY TO DISCUSS YOUR PROJECT?Let's build what's next.
Call (951) 403-5738
LET'S GET TO WORK

Power your next project
with confidence.

Talk through your switchgear and power distribution needs with our team.

Call (951) 403-5738
Request a Quote