NEW AMERICAN-MADE POWER DISTRIBUTIONSERVING DALLAS – FORT WORTH
Motor-control equipment lineup inside a warehouse
NEW EQUIPMENT FOR DALLAS–FORT WORTH

1600 A Switchgear Device and Access Choices

Compare fixed and drawout device choices for a 1600 A project, including access, short-circuit data, drawings and assumptions to resolve.

MADE IN USAAmerican components
UL 891Switchboard assemblies
SHORT LEAD TIMESConfirm your project schedule
BUILT FOR YOUR PROJECT

Power distribution, with purpose.

A 1600 A figure is a project input, not a complete switchgear design or confirmation that a particular assembly is available. Device construction, bus arrangement, fault duty, operating conditions, and maintenance approach all affect what is appropriate. For a new 1600 A application, compare fixed and drawout arrangements against the actual loads and site constraints, then document unresolved assumptions before requesting a quote. The manufacturer builds new equipment and can review custom configurations; actual capabilities, component availability, ratings, standards, and any U.S.-origin requirements must be confirmed for the specific order.

Start with what “1600 A” means in the system

Clarify whether 1600 A is the expected continuous load, a main-device frame or trip value, a feeder requirement, or a preliminary target. Those are not interchangeable. Provide system nominal voltage and phase, grounding arrangement, frequency, expected demand and growth, and the function of each main or feeder device. A nominal system voltage is also distinct from equipment maximum rating; both need to be stated or confirmed rather than inferred from an ampere figure.

Load details help reveal whether the proposed current basis fits actual operating conditions. Supply load schedules, motor and transformer data, major non-linear loads, duty cycles, and any planned additions. Identify loads that must remain energized during maintenance or an outage. If the 1600 A value comes from an existing one-line or a consultant’s basis of design, include that document and note its assumptions instead of treating the value as independently validated.

Compare fixed and drawout device construction

A fixed device is installed in a set position and connected as part of the assembly. This can suit applications where the operating arrangement is stable and the maintenance plan does not call for withdrawing the device. Confirm how isolation is achieved, what upstream and downstream switching is available, and whether work on a fixed device would require a broader outage. Required clearances and the access path for inspection or replacement still matter even when the device itself does not move.

A drawout device is designed to move between defined positions, subject to the specific equipment and device design. It may support a different isolation and maintenance strategy, but it brings requirements for compartment dimensions, shutters or barriers where applicable, interlocks, racking clearance, and a practical route to remove and handle the device. Ask whether the intended device and assembly combination is available and suitable for the project. Do not assume drawout construction is available at every voltage, current, or fault rating, or that it eliminates the need for an outage.

Illustrative close-up of copper busbars in a motor control panel
Illustrative industry photograph · ToT89 / Wikimedia Commons · resized · CC BY-SA 4.0

Treat access as an operational requirement

Provide room dimensions and an equipment-room plan showing front and rear working areas, side clearances, door swings, columns, cable trenches, overhead obstructions, and the path from the delivery opening to the final position. Identify whether access is front-only or whether rear access is possible. For drawout equipment, show space for device movement and any intended storage or service position; for fixed equipment, show how technicians would reach terminations and serviceable parts. These constraints can change the lineup arrangement before fabrication.

Consider the full service task, not only normal operator standing space. Record how the assembly will be transported, positioned, and connected, as well as restrictions on lifting, floor loading, and access through occupied areas. The purchaser should identify who is responsible for installation and site coordination; equipment supply should not be mistaken for an installation commitment. For Dallas–Fort Worth projects, as for shipments elsewhere, site access and delivery constraints should be confirmed by the purchaser and project team rather than assumed from the service region.

Establish short-circuit duty from system data

A 1600 A continuous-current requirement does not establish the available fault current or the assembly’s short-circuit capability. Supply the latest utility fault-current information or a study, transformer kVA and impedance, source configuration, conductor and bus data where known, and details of generators or other sources that can operate in parallel. Include protective-device types and settings when available. State the intended voltage and any required withstand or interrupting values, and identify whether the requirement applies to a main device, a feeder, the bus, or the complete assembly.

Compare alternatives only against a defined fault-duty basis and protection scheme. Higher short-circuit requirements can affect device selection, bus bracing, enclosure configuration, and component availability; protective coordination may also influence the choice between fixed and drawout arrangements. Engineering review must confirm the applicable ratings and standards for the specific order. UL 891 concerns low-voltage switchboards and should not be treated as a general listing for medium-voltage switchgear; voltage class and equipment type need to be established first.

Send a quote package that exposes assumptions

A useful request includes the one-line diagram, load schedule, equipment and room drawings, voltage and grounding details, fault-current basis, and the project specification. Add control schematics or sequence requirements if the assembly must interface with transfer equipment, generators, remote operation, metering, or building controls. State preferred fixed or drawout construction and explain the maintenance reason behind that preference. Include applicable standards, documentation needs, environmental conditions, and any U.S.-origin clauses for review rather than presuming they apply in a particular way.

Separate confirmed requirements from open questions in the request. Examples include whether rear access is feasible, whether future feeder spaces are needed, which loads require continuity, who supplies protective settings, and whether the available fault-current study reflects the final source arrangement. Ask the manufacturer to identify exceptions, required clarifications, and component availability before the design is finalized. Custom builds and shorter lead time are goals, not guarantees; timing and all project-specific capabilities must be verified for the order. This process makes a comparison meaningful without presenting 1600 A as a complete design or an assured product offering.

PROJECT CONSIDERATIONS

Specifications & planning

Review the details that matter for your application. Final specifications and availability should be confirmed for your project.

1600 A application: specifications and planning considerations
Evaluation factorInformation to establish
Current basisLoad demand, device function, growth, and operating duty
ConstructionFixed or drawout preference and maintenance rationale
AccessFront/rear clearances, withdrawal space, and delivery path
Fault dutyStudy basis, source configuration, and required assembly/device ratings
READY TO DISCUSS YOUR PROJECT?Let's build what's next.
Call (951) 403-5738
LET'S GET TO WORK

Power your next project
with confidence.

Talk through your switchgear and power distribution needs with our team.

Call (951) 403-5738
Request a Quote