NEW AMERICAN-MADE POWER DISTRIBUTIONSERVING DALLAS – FORT WORTH
Installed switchgear below conduit in an equipment room
NEW EQUIPMENT FOR DALLAS–FORT WORTH

2000 Amp Switchgear Specification Guide

Plan a 2000 A switchgear specification by separating continuous current from trip settings and fault ratings, then verify load and enclosure conditions.

MADE IN USAAmerican components
UL 891Switchboard assemblies
SHORT LEAD TIMESConfirm your project schedule
BUILT FOR YOUR PROJECT

Power distribution, with purpose.

A 2000 A switchgear specification is a planning point for continuous current, not a complete description of how an assembly will perform. For a distribution lineup with several major feeders, the main rating, feeder protection, fault-duty capability, site conditions and room for future circuits must be coordinated. Treat 2000 A as an example requirement to validate against the project’s calculations and the manufacturer’s available configurations.

Define what the 2000 A figure represents

In this guide, 2000 A means an example continuous-current specification for the relevant switchgear bus or main path, as defined in the project documents. It does not mean that every feeder is rated 2000 A, that the load should draw that much current at all times, or that protective devices should trip at exactly 2000 A. The specification should identify which components and sections the rating applies to, along with the applicable equipment rating and operating conditions.

Keep continuous-current capacity separate from protection settings and fault performance. A breaker trip setting determines how its protective function responds under specified conditions; available fault current is the prospective current at a point in the system; and interrupting rating concerns a device’s ability to interrupt current under stated conditions. These values answer different questions and must be checked against one another. A 2000 A designation alone establishes neither a suitable trip setting nor adequate fault-duty capability.

Build the load case from actual feeder demand

For a lineup serving multiple major feeders, assemble the expected loads by feeder rather than adding equipment nameplate currents indiscriminately. The responsible electrical designer should apply the project’s load calculation method, account for the nature and duration of loads, and document assumptions about demand, diversity, motor starting, future loads and operating schedules. The resulting calculated demand can then be compared with the proposed continuous-current specification and the intended loading of each feeder.

A useful quote package distinguishes existing load from planned additions and identifies which loads can operate simultaneously. It should also show the system nominal voltage, phase and wire configuration, source arrangement, feeder quantities and approximate feeder requirements. If the load forecast is uncertain, describe that uncertainty instead of treating a rough estimate as a settled design. This helps prevent selecting a bus rating that appears adequate on paper but leaves no practical margin for the expected operating pattern.

Illustrative close-up of copper busbars in a motor control panel
Illustrative industry photograph · ToT89 / Wikimedia Commons · resized · CC BY-SA 4.0

Coordinate bus rating, breakers and fault duty

A switchgear lineup is a coordinated assembly, not just a bus with a single current label. Main and feeder breaker frame sizes, sensor or rating-plug choices where applicable, trip functions, bus arrangement and connection details affect how the design fits the distribution plan. The requested 2000 A continuous-current value must be evaluated for the actual assembly and its components; configuration and rating availability should be confirmed for the specific order rather than assumed from a general product description.

Provide the available fault-current study or the information needed to establish it, including the source and relevant system conditions. The design review must compare that value with the applicable short-circuit ratings and device interrupting ratings, using the correct voltage and system arrangement. A higher continuous-current specification does not automatically provide greater fault capability. Ratings, component availability, applicable standards and any U.S.-origin requirements need project-specific confirmation before the specification is finalized.

Check ambient, enclosure and installation conditions

Current capability depends on more than the number printed beside the bus rating. Report the expected ambient conditions, indoor or outdoor setting, enclosure requirements, ventilation constraints, altitude if relevant, and any unusual heat sources or contaminants near the equipment. Room dimensions and access routes matter too: a lineup that fits electrically may be difficult to position, connect or maintain if doorways, clearances, working space or cable entry locations were not considered early.

For a Dallas–Fort Worth project, provide the actual building or site conditions rather than relying on a regional assumption. Outdoor exposure, mechanical-room temperature, dust, moisture and available space vary by installation. Confirm the enclosure and environmental details with the project engineer and manufacturer, and check that the selected configuration is suitable for the intended location. Do not infer equipment ratings or environmental suitability solely from the 2000 A current specification.

Make expansion and interfaces part of the design

When several major feeders share a lineup, reserve space and capacity based on a defined expansion plan. Identify likely future feeder sizes, preferred section locations and whether spare ways need to be fully equipped or only reserved. Physical space, bus arrangement and future electrical demand are separate planning issues: an empty section does not by itself guarantee that a later addition will fit the original current, fault-duty or protection assumptions.

Document connections to upstream and downstream equipment, including source details, cable or busway entry and exit, metering needs, control power, communications and any required interlocks. These interfaces can drive section layout and component selection. If the system may change, such as through a future source addition or operating configuration change, flag it for engineering review now. A clear boundary between current scope and anticipated changes makes the quote more useful and reduces the risk of treating an unverified future condition as covered.

Prepare a quote request that supports review

For a useful quote request, send the one-line diagram, load schedule, system voltage and configuration, calculated load basis, available fault-current information, feeder list, enclosure and environmental requirements, physical layout constraints, and any project specifications. State whether 2000 A is a required continuous rating, a preliminary target or a value taken from an existing design. Include schedule needs and identify any standards, documentation or U.S.-origin requirements that apply, so they can be checked rather than presumed.

The manufacturer builds and supplies new custom equipment, with American components and a shorter lead time as a goal; actual components, configuration and schedule must be confirmed for the order. UL 891 applies to low-voltage switchboards where applicable, not generally to medium-voltage switchgear, and it should not be assumed for every assembly. Final ratings and standards depend on the specified design and review. Purchasers in Dallas–Fort Worth and elsewhere can support that review by supplying complete project data before configuration is settled.

PROJECT CONSIDERATIONS

Specifications & planning

Review the details that matter for your application. Final specifications and availability should be confirmed for your project.

2000 A continuous-current planning: specifications and planning considerations
Evaluation factorInformation to confirm
Continuous-current basisBus or main-path rating required; calculated demand and loading assumptions
Protection and fault dutyTrip functions and settings; available fault current; applicable interrupting and short-circuit ratings
Site conditionsAmbient, indoor or outdoor use, enclosure needs, access and installation constraints
Expansion and interfacesFuture feeder plan, source arrangement, cable or busway connections and controls
READY TO DISCUSS YOUR PROJECT?Let's build what's next.
Call (951) 403-5738
LET'S GET TO WORK

Power your next project
with confidence.

Talk through your switchgear and power distribution needs with our team.

Call (951) 403-5738
Request a Quote