NEW AMERICAN-MADE POWER DISTRIBUTIONSERVING DALLAS – FORT WORTH
Installed switchgear below conduit in an equipment room
NEW EQUIPMENT FOR DALLAS–FORT WORTH

12.47 kV Switchgear Specification Guide

Plan a 12.47 kV switchgear specification with clear grounding, voltage, protection, insulation and service-interface requirements for engineering review.

MADE IN USAAmerican components
UL 891Switchboard assemblies
SHORT LEAD TIMESConfirm your project schedule
BUILT FOR YOUR PROJECT

Power distribution, with purpose.

A 12.47 kV system specification begins with the electrical network, not a catalog label. Define whether 12.47 kV is the nominal three-phase line-to-line voltage, how the source is grounded, and what the equipment must withstand and interrupt. These choices affect voltage sensing, insulation coordination, protective-device settings and the connection to the utility or adjacent equipment. A 12.47 kV configuration should not be assumed available from a manufacturer until its specific design, components and ratings have been confirmed for the project.

State the system voltage and phase relationships

For a typical three-phase system designated 12.47 kV, the nominal value is line-to-line: the voltage measured between phases. In a grounded-wye system, the corresponding nominal line-to-neutral value is approximately 7.2 kV, calculated by dividing 12.47 kV by the square root of three. That relationship is useful for understanding grounding and voltage-transformer connections, but it does not make the system a 7.2 kV line-to-line system. Confirm the utility’s stated nominal voltage and actual configuration rather than inferring them from a drawing or a legacy equipment label.

The specification should distinguish nominal system voltage from the switchgear’s rated maximum voltage and insulation levels. Equipment must be suitable for the system’s operating conditions, including expected voltage variation and overvoltage exposure; selecting by the nominal number alone is not enough. Identify the applicable equipment class and request confirmation of the proposed voltage rating, insulation withstand values and intended application. Do not assume a particular 12.47 kV assembly is offered or suitable until the manufacturer reviews the one-line diagram and project requirements.

Describe grounding and ground-fault conditions

State whether the source is solidly grounded, resistance grounded, reactance grounded, ungrounded or grounded by another defined arrangement. For resistance-grounded systems, provide the grounding resistor’s continuous and short-time ratings and the intended ground-fault current or alarm/trip strategy. Grounding affects phase-to-ground voltage during a fault, ground-fault detection, insulation stress and the way protective relays interpret residual or zero-sequence quantities. If the system can be supplied from multiple sources, describe each source and the permitted operating combinations.

Identify the grounding connection and relevant interfaces, including neutral grounding equipment, grounding transformers, cable shields and the switchgear ground bus as applicable. A grounded-wye line-to-neutral value is not necessarily the voltage experienced by every component during an abnormal condition. The engineer should evaluate temporary overvoltage and ground-fault clearing time against the proposed insulation design. Provide grounding studies or design criteria with the quote request when available, and flag any operating modes that could change the effective grounding method.

Illustrative close-up of copper busbars in a motor control panel
Illustrative industry photograph · ToT89 / Wikimedia Commons · resized · CC BY-SA 4.0

Specify frequency, duty and interruption requirements

For U.S. projects, state the required system frequency, typically 60 Hz, rather than leaving it implicit. Also define continuous load current, load type, expected switching duty and the maximum available fault current at the switchgear terminals. Available short-circuit current depends on the source and system configuration; it is not established by the 12.47 kV nominal voltage. Supply the latest utility fault data or study results, including the assumptions and point of calculation, so equipment and protective devices can be evaluated against the actual duty.

Clarify whether the assembly is intended for service entrance, feeder distribution, motor loads, transformers, generators or a combination. Interrupting and short-time withstand requirements are related but distinct: the protective device must interrupt the assigned fault duty, while the assembly and bus must withstand the specified fault current for the applicable duration. Identify future source changes or load additions that could raise fault levels. All proposed short-circuit ratings, component availability and applicable standards require confirmation for the specific order and design.

Coordinate insulation and surge protection

Insulation coordination considers more than normal operating voltage. Provide the system’s grounding method, expected switching events, exposure to lightning or other surges, cable lengths and the protection scheme at the source and load interfaces. Specify required power-frequency and impulse withstand criteria where the project documents define them, and ask the equipment manufacturer and engineer to confirm that the proposed design is appropriate. Surge arresters, if required, must be selected and located for the system configuration and coordination objective; a generic arrester designation does not establish adequate protection.

Cable termination details can influence the physical arrangement and insulation clearances. Identify cable type, conductor size and material, number of cables per phase, termination style, shield treatment, entry direction and any limits on bending space. Include elevation or enclosure constraints that could affect terminations and access. Where outdoor exposure, altitude, contamination or unusual ambient conditions apply, state them explicitly because these conditions may affect insulation and enclosure decisions. Project-specific ratings and design suitability should be reviewed before release for manufacture.

Set protection and service boundaries

Provide the intended protective-device functions and coordination objectives, not just a preferred relay name. Relevant inputs may include transformer inrush, motor starting, downstream fuse or relay curves, ground-fault sensitivity, breaker-failure logic and upstream utility protection. Identify required CT and VT ratios, accuracy or burden needs, polarity and connection details, metering points, trip circuits and control power. These items determine whether the protection can detect and clear faults selectively while avoiding unwanted operation during normal system events.

Define the boundary between the switchgear and connected equipment: incoming source conductors, outgoing feeders, bus ties, transformers, grounding equipment, control wiring and communications. State normal and alternate operating states, interlocking expectations and any required interface signals. Coordination across this boundary is particularly important when utility protection, customer-owned relays and downstream devices are supplied by different parties. For Dallas–Fort Worth projects as well as shipments elsewhere, the same complete interface information supports a meaningful design review; service to a region does not imply a local manufacturing facility.

Prepare a quote package for the actual configuration

A useful request for quotation includes the one-line diagram, nominal voltage and frequency, grounding description, load schedule, available fault-current data, protection and metering requirements, cable and termination information, environmental conditions and applicable project specifications. Add required compartment arrangement, bus configuration, enclosure conditions, control voltage, communications and delivery destination. Identify governing standards and any U.S.-origin or component requirements, since these must be checked against the specific design and supply chain rather than presumed.

The manufacturer builds new equipment and can review a custom configuration, but that does not establish that every 12.47 kV arrangement, component combination or schedule is available. Ask for confirmation of the proposed rated voltage, insulation and short-circuit capabilities, included devices, exclusions and expected lead time before treating the offer as suitable. Shorter lead time may be a goal, not a guarantee; engineering review, component availability and approved drawings affect the schedule. If the request involves low-voltage switchboards elsewhere in the project, UL 891 applies to that equipment category, not as a general listing for medium-voltage switchgear.

PROJECT CONSIDERATIONS

Specifications & planning

Review the details that matter for your application. Final specifications and availability should be confirmed for your project.

12.47 kV voltage planning: specifications and planning considerations
Evaluation factorInformation to establish
System voltageNominal line-to-line voltage; confirm line-to-neutral relationship and source configuration
GroundingGrounding method, ground-fault current and clearing-time assumptions
Fault dutyAvailable short-circuit current at the equipment location and study basis
Insulation coordinationWithstand criteria, surge exposure and protective-device interfaces
Quote inputsOne-line, load data, cable details, protection requirements and project constraints
READY TO DISCUSS YOUR PROJECT?Let's build what's next.
Call (951) 403-5738
LET'S GET TO WORK

Power your next project
with confidence.

Talk through your switchgear and power distribution needs with our team.

Call (951) 403-5738
Request a Quote