NEW AMERICAN-MADE POWER DISTRIBUTIONSERVING DALLAS – FORT WORTH
Gray electrical switchgear cabinets with breaker panels
NEW EQUIPMENT FOR DALLAS–FORT WORTH

Secondary-Selective Distribution Architecture

Learn how secondary-selective distribution uses alternate sources and a tie breaker, and what engineers must evaluate before specifying the architecture.

MADE IN USAAmerican components
UL 891Switchboard assemblies
SHORT LEAD TIMESConfirm your project schedule
BUILT FOR YOUR PROJECT

Power distribution, with purpose.

Secondary-selective distribution connects two power sources to separate sections of a low-voltage distribution system, with a bus tie that can link the sections when a source is unavailable. The arrangement can preserve service to selected loads, but it is not inherently redundant: the result depends on source independence, protective-device coordination, transfer logic and the loads permitted on the alternate source. A sound design starts with the failure the owner wants to ride through and the loads that must remain energized—not simply a preference for two incoming feeds.

Define the sources and the operating states

A typical arrangement has two incoming sources, two main breakers and a tie breaker between bus sections. In normal operation, each source supplies its own section and the tie is open. If a source fails or is intentionally removed, the affected main is opened and the tie may close so the remaining source can serve both sections. Some designs use automatic transfer; others require operator action. The specified sequence must prevent unintended paralleling unless the sources, controls and protection are expressly designed and approved for parallel operation.

Do not assume two utility service entrances are independent. Establish whether sources share a substation, feeder route, transformer, upstream breaker, control-power supply or other failure point. If one source is a generator or another on-site source, confirm its ability to accept the transferred load, including motor starting, nonlinear loads, step changes and required duration. Document the normal and contingency states, including which loads transfer, which are shed, and whether transfer is open-transition or another engineered arrangement.

Collect the data that makes the choice defensible

Before selecting equipment, gather the one-line diagram, service and source information, system nominal voltage, frequency, grounding method, available fault current at each source, and the utility’s applicable requirements. Engineers also need load schedules with demand assumptions, motor and transformer data, critical-load priorities, future expansion, environmental conditions and the required short-circuit and interrupting ratings. Source data should distinguish nominal system voltage from the equipment’s maximum voltage rating; those values are related but not interchangeable.

The design team should resolve how metering, protective relays, control power, communications, alarms and interlocks interface with the switchboard and upstream sources. Specify whether transfer is automatic or supervised, what initiates transfer, how an unsuccessful transfer is indicated, and what conditions block closing the tie. Define restoration behavior as well: automatic retransfer may cause another interruption or load step, while manual restoration can require operator availability. Final logic and settings belong to qualified electrical professionals using project data.

Illustrative close-up of copper busbars in a motor control panel
Illustrative industry photograph · ToT89 / Wikimedia Commons · resized · CC BY-SA 4.0

Test the architecture with a hypothetical decision

Consider a hypothetical facility with two separately routed utility sources and critical loads on both bus sections. The owner wants one source to carry designated critical loads after the other source is lost, but does not require every load to remain online. A secondary-selective arrangement may be a candidate if the surviving source and equipment can carry the transferred demand and if the protection scheme can safely support the changed configuration. A load study might show that noncritical loads must be shed before the tie closes.

If the sources instead share an upstream point of failure, the apparent redundancy may not address the owner’s principal risk. A generator-backed essential-load bus, separate distribution paths, or a different source arrangement may better match the required outage coverage. This example is not a design recommendation for an actual facility. The decision changes with fault-current results, load behavior, transfer time, source constraints, operating staff and the consequences of an interruption; an engineer must validate the assumptions and resulting protection.

Compare alternatives and maintainability

A simple radial system can cost less and is easier to operate, but a source outage generally interrupts its associated loads until an alternate supply is established. A double-ended arrangement with a normally open tie can improve continuity while keeping sources separated in normal operation. A normally closed tie or continuously paralleled sources change current paths and protection requirements, so they should not be treated as minor variations. Separate critical-load distribution or UPS support may address short interruptions more directly, though it adds equipment and maintenance obligations.

Maintainability depends on whether a section can be isolated for inspection or repair without losing required loads, and whether the alternate source can support that condition. Review breaker access, safe isolation points, control-circuit troubleshooting, spare-part strategy and the ability to test transfer logic without creating an unacceptable outage. A tie breaker is a switching resource, not proof that maintenance can proceed without interruption. Operating procedures, arc-flash and coordination studies, equipment condition, and qualified personnel remain essential to safe operation.

Specify records, equipment and review limits

A quote request should provide the current one-line, load and source schedules, enclosure and installation requirements, bus configuration, required device and control functions, available fault-current data, communication interfaces and applicable utility or authority requirements. Include desired transfer sequence, load-shed priorities, metering, spare provisions and any project-specific U.S.-origin or component restrictions. For a Dallas–Fort Worth project, the same engineering inputs matter as elsewhere; delivery planning should also account for site access, receiving constraints and the construction schedule without assuming a local manufacturing facility.

Require coordinated submittals and records appropriate to the project, such as reviewed drawings, elementary and interconnection diagrams, device schedules, settings documentation, test records and final as-built updates. New custom switchboards can be evaluated against the required configuration; UL 891 applies to low-voltage switchboards where applicable, not to medium-voltage gear generally. Confirm the specific assembly’s ratings, standards, component availability and origin requirements before order. The architecture discussion alone does not establish code compliance, select final settings, guarantee transfer performance or replace review by the owner’s engineer, utility and authority having jurisdiction.

PROJECT CONSIDERATIONS

Specifications & planning

Review the details that matter for your application. Final specifications and availability should be confirmed for your project.

Architecture: specifications and planning considerations
Evaluation factorWhat to establish
Source independenceShared upstream risks and separate routing
Transfer behaviorInitiation, interlocks, transition and restoration
Alternate-source capacityTransferred demand, starting loads and shedding
Protection basisFault-current data and operating-state coordination
READY TO DISCUSS YOUR PROJECT?Let's build what's next.
Call (951) 403-5738
LET'S GET TO WORK

Power your next project
with confidence.

Talk through your switchgear and power distribution needs with our team.

Call (951) 403-5738
Request a Quote