NEW AMERICAN-MADE POWER DISTRIBUTIONSERVING DALLAS – FORT WORTH
Motor-control equipment lineup inside a warehouse
NEW EQUIPMENT FOR DALLAS–FORT WORTH

A/B Power Distribution for Data Centers

Plan data center A/B power paths with clear source boundaries, tie logic, coordination inputs, and equipment decisions subject to engineering review.

MADE IN USAAmerican components
UL 891Switchboard assemblies
SHORT LEAD TIMESConfirm your project schedule
BUILT FOR YOUR PROJECT

Power distribution, with purpose.

A/B power distribution is only as resilient as the independence and coordination of its two paths. For a data center, the design must define where each path begins and ends, what a tie can connect, and how protective devices respond to faults without creating an unintended common point of failure.

Define what “independent” means

An A/B designation does not by itself establish redundancy. The project team should trace each path from its source through transformers, service or generator distribution, switchboards, UPS equipment, and downstream distribution to the intended load. Shared utility service, a common generator bus, a single room, or common controls may remain dependencies even when separate A and B conductors appear on a one-line diagram. Record those dependencies so the owner can judge whether they are acceptable.

Set the boundary of the equipment package explicitly. A switchboard manufacturer needs to know which incoming sources, outgoing feeders, metering, protective devices, and tie connections are in scope, and which are supplied or controlled by others. A low-voltage switchboard may be specified as a UL 891 assembly where applicable, but that designation does not establish end-to-end data center redundancy or cover medium-voltage gear. Confirm system nominal voltage, equipment ratings, fault duties, and applicable standards for the actual order.

Make tie logic deliberate

A bus tie can support planned maintenance or restoration, but it can also defeat separation if it closes across sources that should not operate in parallel. The sequence must state the permitted source combinations, normal tie position, transfer conditions, and whether operation is open-transition or allows any momentary overlap. Address source synchronization, interlocks, control-power dependencies, and the response to loss of sensing or communications rather than relying on the phrase “automatic transfer.”

Coordinate the tie scheme with generator, UPS, and upstream protection behavior. For example, an interlock may prevent closing a tie when both incomers are energized, while a control sequence may require confirmation that a source is available before transfer. The design authority must approve operating modes and failure responses; the equipment supplier should build to the approved logic and identify interface points, not infer facility-wide operating policy.

Illustrative close-up of copper busbars in a motor control panel
Illustrative industry photograph · ToT89 / Wikimedia Commons · resized · CC BY-SA 4.0

Coordinate protection across boundaries

A fault on one branch should not unnecessarily interrupt the other path, but selectivity depends on actual device data and available fault current. Gather utility and generator contributions, transformer impedance, conductor information, protective-device models and settings, and downstream UPS or distribution characteristics. Review short-circuit ratings, interrupting ratings, and coordination results together; a nominal voltage match alone does not show that an assembly is suitable for the available fault duty.

Agree who owns the studies and settings at each boundary. The electrical engineer of record may establish system requirements and approve coordination, while upstream utility or generator providers supply source data and downstream vendors provide device information. Document assumptions and revisions because changes to transformer size, generator configuration, or feeder length can affect the result. Do not treat manufacturer fabrication documents as a substitute for the project’s protection and arc-flash engineering.

Illustrative scenario: maintenance transfer

Consider a hypothetical facility with separate A and B low-voltage buses feeding redundant downstream equipment. During planned maintenance on the A-side source, the owner wants selected loads carried from the B side through a tie. The design review would first identify whether B has capacity for those loads, whether its upstream source and conductors support the added duty, and whether the downstream equipment can tolerate the transfer behavior.

The team would then decide which feeders are eligible, what prevents an unintended parallel connection, how operators confirm the source state, and what happens if a breaker or control signal fails. This is an illustration, not a completed project or a claim that a particular configuration is available. The owner and design authority must approve the operating sequence, and the specific assembly and components must be validated against the final drawings and requirements.

Balance resilience, complexity, and space

More separation can reduce shared failure exposure, yet duplicated equipment, additional ties, and more elaborate controls increase footprint, interfaces, maintenance tasks, and commissioning effort. A normally open tie may preserve source separation but leave a transfer step for operators; an automatic scheme can reduce response time while adding sensing, control, and failure-mode questions. Evaluate the intended maintenance strategy and load criticality rather than treating the most complex arrangement as automatically more resilient.

Physical arrangement matters as well. Confirm lineup access, cable entry and exit, room clearances established by the project, segregation requirements, heat and environmental conditions, and routing between A and B. For projects in Dallas–Fort Worth or elsewhere, shipping and site access can affect delivery planning, but no local factory or installation service should be assumed. Custom builds using American components may be considered, with component availability, origin requirements, and any lead-time goals confirmed for the specific order.

Provide a quote package and approval path

For a useful quotation, provide the current one-line diagram, equipment scope boundaries, nominal system voltage and frequency, source and transformer data, available fault-current information, bus and feeder requirements, proposed tie arrangement, and device or metering preferences. Include control narratives, communication interfaces, environmental conditions, dimensional constraints, applicable specifications, desired delivery window, and required submittal documents. Identify assumptions and alternates so a proposal can distinguish confirmed requirements from items still under engineering review.

Before release, the owner and engineer of record should approve the one-line, tie operating philosophy, protection coordination responsibility, and interface schedule. The manufacturer can review the requested configuration and develop new equipment to an agreed scope; final ratings, short-circuit capability, component availability, standards applicability, UL 891 applicability for low-voltage switchboards, and U.S.-origin requirements must be confirmed for the specific order. Approval boundaries should be clear before fabrication, with changes evaluated for technical and schedule effects.

PROJECT CONSIDERATIONS

Specifications & planning

Review the details that matter for your application. Final specifications and availability should be confirmed for your project.

Data Centers: specifications and planning considerations
Evaluation factorDecision to document
Path boundarySources, shared dependencies, and package interfaces
Tie operationNormal position, transfer conditions, and permitted source combinations
Protection basisFault-current inputs, device data, study owner, and settings approval
Quote readinessDrawings, ratings, controls, space limits, and applicable requirements
READY TO DISCUSS YOUR PROJECT?Let's build what's next.
Call (951) 403-5738
LET'S GET TO WORK

Power your next project
with confidence.

Talk through your switchgear and power distribution needs with our team.

Call (951) 403-5738
Request a Quote