NEW AMERICAN-MADE POWER DISTRIBUTIONSERVING DALLAS – FORT WORTH
Switchgear cabinets with doors open on a warehouse floor
NEW EQUIPMENT FOR DALLAS–FORT WORTH

Industrial Switchgear for Facilities

Plan industrial switchgear around motor starting, fault protection, maintainability, and the operating conditions that shape a reliable facility design.

MADE IN USAAmerican components
UL 891Switchboard assemblies
SHORT LEAD TIMESConfirm your project schedule
BUILT FOR YOUR PROJECT

Power distribution, with purpose.

Industrial switchgear must support the way a facility actually runs: motors start and stop, processes change, and maintenance has to fit around production priorities. Selecting an assembly is therefore more than matching a voltage. Buyers should coordinate the electrical design with motor characteristics, upstream and downstream protection, operating practices, and future expansion. A clear specification gives the manufacturer a sound basis for developing a new switchboard or switchgear assembly for review.

Start with the motor operating profile

A motor schedule is a useful starting point, but the connected horsepower alone does not describe the electrical duty. For each motor or motor-control section, identify voltage, full-load current, starting method, frequency of starts, duty cycle, and whether operation is continuous, intermittent, or part of a critical process. Across a lineup, simultaneous starting or restarting after an outage can create a very different demand from normal steady-state operation. These details affect feeder sizing, bus loading, protective-device selection, and the practical organization of the assembly.

Also explain how the motors are controlled and what equipment lies between the switchgear and the load. A direct-on-line starter, reduced-voltage starter, or variable-frequency drive has different interface and protection considerations. Drives may introduce harmonics or require specified input protection, while long motor cable runs and control-system requirements can influence coordination. Share applicable drive and starter data, control schematics, and process sequences rather than expecting a switchgear rating to resolve every motor-system question.

Coordinate protection with the system

Protection must distinguish expected motor behavior from a fault while limiting damage and unnecessary interruption. Starting current and acceleration time matter when evaluating overcurrent-device settings and coordination with downstream motor protection. A device that trips during a normal start disrupts production; a device selected without regard to available fault current can leave equipment inadequately protected. The system study and equipment specification should therefore work together, rather than relying on a generic breaker size or a single short-circuit figure.

Provide the nominal system voltage, grounding arrangement, source and transformer information, available short-circuit current at the proposed connection, and relevant upstream and downstream device data. The equipment maximum voltage rating is not interchangeable with system nominal voltage, and interrupting or short-circuit ratings require confirmation for the actual design. Protection settings and coordination should be reviewed by qualified electrical engineering professionals. Do not treat a preliminary quote as a substitute for a completed coordination or arc-flash study.

Illustrative close-up of copper busbars in a motor control panel
Illustrative industry photograph · ToT89 / Wikimedia Commons · resized · CC BY-SA 4.0

Reliability depends on operating conditions

An industrial lineup may serve loads where a brief interruption has very different consequences across areas of the same plant. Identify which feeders support essential process equipment, which loads can be shed, and whether the operating plan calls for alternate sources, tie arrangements, or future load additions. A bus configuration that improves continuity can also add cost, footprint, controls, and maintenance complexity. Define the consequence of losing a source or section so the design discussion can address an appropriate balance rather than assuming that more equipment always means greater reliability.

Describe the installation environment as carefully as the one-line diagram. Ambient temperature, dust, moisture, corrosive substances, elevation, ventilation, and indoor or outdoor placement can influence enclosure and component decisions. Tell the manufacturer about equipment-room access, cable entry direction, available floor space, and working clearances established by the project design. Facilities in Dallas–Fort Worth and elsewhere may have different site conditions; regional service does not establish that a manufacturer has a local factory or that a particular enclosure is suitable without review.

Make maintainability part of the specification

Maintenance needs are shaped by how operators isolate, inspect, test, and replace components, as well as by the time available for planned outages. Specify the desired compartment arrangement, access needs, device types, metering, control power, indication, and communications interfaces. Where plant procedures require isolation of one section while other loads remain in service, explain the intended work boundaries and operating sequence. The assembly design must be evaluated against the facility’s safety practices and applicable engineering requirements; a particular arrangement should not be assumed to provide a specific level of isolation unless confirmed.

Consider the lifecycle of installed devices and the ability to obtain compatible replacement components over the expected service period. Record existing manufacturer and model information when the new equipment must interface with retained gear, protective relays, drives, or building controls. Confirm terminal locations, wiring conventions, communication protocols, and available control voltages early. Custom construction can address project-specific layouts and interfaces, but component availability, interchangeability, and future expansion provisions must be verified for each order.

Prepare a complete quote package

A useful request for quotation includes the one-line diagram, load and motor schedules, system voltage and frequency, grounding details, fault-current data, protection requirements, and the applicable project specifications. Add the preferred lineup dimensions, cable-entry and termination requirements, environmental conditions, control and metering needs, and any required interfaces with existing equipment. Identify applicable standards, documentation expectations, and delivery constraints. If a study or design detail is not yet available, label it as pending rather than presenting an unverified assumption as a final requirement.

The manufacturer builds and supplies new equipment, including custom assemblies using American components when specified and available. Shorter lead time may be a project goal, not a guarantee; the schedule depends on the approved design, component availability, and order-specific requirements. UL 891 applies to low-voltage switchboards, not generally to medium-voltage equipment, and a particular assembly’s applicable standard or status must be confirmed. For Dallas–Fort Worth projects or shipments elsewhere in the United States, provide the destination and receiving constraints so delivery planning can be evaluated without assuming a local installation service.

PROJECT CONSIDERATIONS

Specifications & planning

Review the details that matter for your application. Final specifications and availability should be confirmed for your project.

Industrial: specifications and planning considerations
Evaluation factorInformation to define
Motor dutyStarting method, acceleration time, start frequency, and operating sequence
Protection basisSystem study inputs, available fault current, and coordination interfaces
Installation conditionsEnvironment, access, cable entry, and equipment-room constraints
MaintainabilityIsolation needs, device preferences, controls, and future replacement strategy
Quote readinessOne-line, schedules, specifications, destination, and unresolved design assumptions
READY TO DISCUSS YOUR PROJECT?Let's build what's next.
Call (951) 403-5738
LET'S GET TO WORK

Power your next project
with confidence.

Talk through your switchgear and power distribution needs with our team.

Call (951) 403-5738
Request a Quote