NEW AMERICAN-MADE POWER DISTRIBUTIONSERVING DALLAS – FORT WORTH
Electrical switchgear along an equipment-room aisle
NEW EQUIPMENT FOR DALLAS–FORT WORTH

Main-Lug-Only Distribution Switchboard Applications

Understand when a main-lug-only distribution switchboard fits, what upstream protection must provide, and which project details to confirm before ordering.

MADE IN USAAmerican components
UL 891Switchboard assemblies
SHORT LEAD TIMESConfirm your project schedule
BUILT FOR YOUR PROJECT

Power distribution, with purpose.

A main-lug-only (MLO) distribution switchboard has incoming line terminals and distribution devices, but no integral main circuit breaker or switch. Its suitability depends on where the installation’s overcurrent protection is located and how that upstream device protects the switchboard and downstream circuits. Confirm the arrangement against the one-line diagram, applicable codes, equipment ratings, and the authority having jurisdiction before specifying or ordering an MLO assembly.

What the MLO configuration includes—and leaves out

In an MLO switchboard, incoming conductors terminate at main lugs; feeder breakers or other distribution devices provide outgoing circuit protection. Because the switchboard itself has no main overcurrent device, protection must come from an upstream device, such as a breaker or fused switch in another assembly. That device’s location, rating, trip characteristics, and relationship to the MLO equipment are part of the design—not details to assume from the switchboard name.

An integral-main configuration places a main device in the switchboard, which can create a local means of disconnect and define a protective boundary at that equipment. An MLO arrangement may reduce duplicated devices or suit a distribution layout already protected upstream, but it does not automatically provide equivalent isolation, selective coordination, or fault protection. The exact functions depend on the specified device and system design.

Trace protection from the source to the switchboard

Start by identifying every device between the source and the MLO incoming lugs. Establish which device is intended to protect the incoming conductors and switchboard, and verify its interrupting or short-circuit capability and protective settings against available fault current and the equipment’s marked ratings. The review must account for conductor type, size, length, installation conditions, and any applicable code rules; an MLO label alone does not establish a complete protection scheme.

Coordination is an interface across equipment boundaries. The upstream protective device may be in a service section, transformer secondary arrangement, or separate distribution lineup, while feeder devices reside in the MLO switchboard. The engineer of record should assess time-current behavior, selective coordination requirements where applicable, and the effect of maintenance or fault conditions. Provide the upstream device data and coordination study assumptions for review; do not treat a nominal ampere rating as proof of coordination or adequate fault protection.

Illustrative close-up of copper busbars in a motor control panel
Illustrative industry photograph · ToT89 / Wikimedia Commons · resized · CC BY-SA 4.0

Representative design scenario: a protected feeder serving an MLO board

Consider a hypothetical facility distribution design in which a separately specified upstream breaker feeds an MLO switchboard, and the switchboard supplies several downstream branch or feeder circuits. The arrangement may be worth evaluating when the upstream breaker already serves as the intended protective device and the project’s design permits the MLO board to have no local main. The scenario is illustrative only; it does not establish that a particular configuration is available or suitable for a project.

Before selecting it, the design team would confirm the source and system nominal voltage, phase and wire arrangement, incoming conductor routing, upstream device details, available fault current, and required equipment short-circuit rating. It would also resolve grounding and bonding, neutral treatment, service-entrance status if relevant, working space, disconnecting means, and any project or jurisdictional requirements. If a local main or disconnect function is required, the MLO concept may not meet the need without a different arrangement.

Tradeoffs, operating boundaries, and project interfaces

A potential benefit of MLO is avoiding a second main device where the upstream design already provides the required protection and isolation. Potential drawbacks include a disconnecting means located away from the switchboard, additional coordination and documentation across equipment, and reduced flexibility if the source arrangement changes. Maintenance planning must account for the actual isolation point and site procedures. Qualified personnel and the project’s safety program determine how equipment is made safe; this page is not an instruction for energized work.

The specification should make the boundary between the upstream assembly, field conductors, and switchboard clear. State who provides the upstream protective device, who verifies its settings, and which party supplies fault-current and coordination information. Identify whether the switchboard is service equipment or downstream distribution, the intended connection and termination provisions, and any enclosure, access, metering, or control requirements. Approval drawings and submittals should be checked by the responsible engineer and relevant reviewing authority before release for manufacture.

Quote inputs, availability, and approval limits

For a useful quote request, provide the current one-line diagram and specification, system nominal voltage, phase and wire details, bus and feeder requirements, incoming cable or busway information, and the upstream protective-device manufacturer, type, rating, and trip or fuse data. Include available fault current at the proposed connection point, required short-circuit rating, enclosure and environmental conditions, metering or control needs, delivery destination, and any required standards or U.S.-origin provisions. Incomplete upstream information can prevent a meaningful review of an MLO design.

The manufacturer builds and supplies new custom switchboard equipment, with American components and shorter lead time as a goal; specific configuration, component availability, schedule, and U.S.-origin requirements must be confirmed for each order. UL 891 applies to low-voltage switchboards, but no particular assembly’s listing or compliance should be assumed without order-specific confirmation. Customers in Dallas–Fort Worth and elsewhere can submit project requirements for review. Final equipment selection, protection design, code interpretation, and approval remain subject to the responsible engineer, applicable authorities, and confirmed manufacturer documentation.

PROJECT CONSIDERATIONS

Specifications & planning

Review the details that matter for your application. Final specifications and availability should be confirmed for your project.

Distribution Switchboards: specifications and planning considerations
Evaluation factorInformation to confirm
Upstream protectionDevice location, type, rating, and settings
Fault-duty basisAvailable fault current and required equipment rating
Disconnecting meansRequired isolation point and service-equipment status
Design coordinationOne-line diagram, study assumptions, and approval responsibilities
READY TO DISCUSS YOUR PROJECT?Let's build what's next.
Call (951) 403-5738
LET'S GET TO WORK

Power your next project
with confidence.

Talk through your switchgear and power distribution needs with our team.

Call (951) 403-5738
Request a Quote