NEW AMERICAN-MADE POWER DISTRIBUTIONSERVING DALLAS – FORT WORTH
Gray electrical switchgear cabinets with breaker panels
NEW EQUIPMENT FOR DALLAS–FORT WORTH

Main and Distribution Switchboard Sections

Compare incoming main and downstream feeder sections, shared-bus planning, coordination interfaces, quote inputs, and approval limits for low-voltage.

MADE IN USAAmerican components
UL 891Switchboard assemblies
SHORT LEAD TIMESConfirm your project schedule
BUILT FOR YOUR PROJECT

Power distribution, with purpose.

A low-voltage switchboard lineup may place the incoming main section beside sections that distribute power to downstream loads, but those sections serve different purposes and impose different design demands. Planning them together matters because they can share a bus, enclosure arrangement, and protection strategy. The right configuration depends on the source, connected loads, fault-current conditions, and project boundaries—not simply the number of feeders.

The incoming main section establishes the source interface

The main section receives power from the upstream source and provides the specified means of switching and protecting the incoming connection. Its design depends on the source arrangement and the project’s requirements for the main device, metering, control power, and cable or bus connections. The main device’s continuous-current rating and interrupting or short-circuit capability are distinct considerations; neither should be inferred from a system’s nominal voltage or from the size of the downstream loads.

The purchaser should clarify whether the source is a utility transformer, generator, or another assembly, and identify the available fault current or the process for establishing it. Source grounding, neutral treatment, phase configuration, and any transfer equipment also affect the interface. Equipment maximum voltage rating must be appropriate for the system nominal voltage, with both confirmed for the specific order. These details help prevent a quote from assuming an incoming arrangement that does not match the one-line diagram.

Feeder sections divide the shared bus among loads

Downstream feeder sections take power from the lineup bus and route it through individual protective devices to loads or separate distribution equipment. Feeder count alone is not enough to define a section: each circuit may have different load current, conductor termination needs, protective-device type, metering, or control requirements. Future spare ways can be useful, but an empty space is not automatically a fully equipped, usable feeder position.

A shared bus makes the lineup a coordinated assembly rather than a collection of independent cabinets. Bus current capacity, temperature limits, bracing for available fault current, physical joints, and device arrangements must work together across the proposed sections. A change in one feeder device or section layout may affect bus space, cable access, heat, or the overall assembly design. Confirm the requested short-circuit ratings and applicable standards for the complete configuration; UL 891 applies to low-voltage switchboards, but no particular assembly’s listing or compliance should be assumed without confirmation.

Illustrative close-up of copper busbars in a motor control panel
Illustrative industry photograph · ToT89 / Wikimedia Commons · resized · CC BY-SA 4.0

Representative planning scenario: one source, several building loads

Consider a hypothetical facility with one incoming source and separate feeder circuits for HVAC equipment, process loads, and a panelboard. The main section would be arranged around the source connection and specified main protective device. Adjacent feeder sections would be laid out according to each circuit’s device and termination requirements, while a common bus carries power between the incoming and outgoing positions. This is a planning example, not a completed customer project or a statement of available standard configurations.

The design team would compare the operating load and expected growth against the proposed main and feeder arrangements, then review the available fault current and protection requirements. A spare feeder position might support later expansion, but reserving it can require additional space and an agreed approach to future bus and protection changes. The final section count and arrangement should follow the approved one-line, load information, and equipment interfaces rather than a generic lineup template.

Quote inputs should define both circuits and physical interfaces

For a useful quote, provide the current one-line diagram, system nominal voltage and phase, source details, available fault-current information, and the required main and feeder device functions. Include load or feeder schedules with circuit quantities and relevant current requirements, along with metering, control, neutral, and grounding needs. Identify applicable project specifications, requested standards, and any US-origin or component restrictions so they can be checked for the particular order.

Physical and delivery information matters too. State the preferred lineup location, access or working-space constraints, cable-entry direction, conductor sizes and termination preferences when known, and any coordination requirements with upstream or downstream equipment. Include the desired shipping destination and timing target; a shorter lead time may be a goal, but component availability and engineering review determine what can be confirmed. The manufacturer builds new equipment and can evaluate custom arrangements using American components where specified, subject to availability and order review.

Coordinate protection, connections, and scope before release

Protection coordination crosses the boundary between the switchboard and connected systems. The engineer or responsible project team should establish device settings and coordination requirements using the actual upstream protective device, downstream equipment, and fault-current study. The switchboard quote cannot by itself confirm system-wide selectivity, arc-flash results, or suitability of connected conductors. Clarify who supplies external cables, upstream disconnects, control wiring, communications, and any field-installed accessories.

Approval boundaries should be explicit before drawings are released for manufacture. The purchaser and project engineer remain responsible for validating the one-line, load assumptions, protection study, code requirements, and interfaces with utility or facility systems. Review submitted drawings for device locations, ratings, bus arrangement, entry points, dimensions, and connection details. Changes after approval may affect engineering, component selection, cost, or schedule, so resolve open items before authorization.

Confirm configuration and availability for the specific order

Main and feeder sections can be custom-built as a coordinated low-voltage switchboard, but that does not mean every device combination, bus arrangement, rating, or component is universally available. Ratings, short-circuit capability, standards, component supply, and any US-origin requirements must be confirmed against the specific project and order. UL 891 is relevant to low-voltage switchboards; it should not be used to describe medium-voltage equipment.

For Dallas–Fort Worth projects and shipments elsewhere in the United States, provide the same technical inputs and delivery constraints early enough for review. A manufacturer can assess the requested layout and work toward a shorter lead time, but should confirm availability and schedule rather than promise them in advance. Use the evaluation factors below as a starting point for project discussions, not as offered ratings or approved design values.

PROJECT CONSIDERATIONS

Specifications & planning

Review the details that matter for your application. Final specifications and availability should be confirmed for your project.

Low-Voltage Switchboards: specifications and planning considerations
Evaluation factorWhat to establish
Source and mainSource type, nominal voltage, phase, main function, and connection
Shared busRequired capacity, fault-current basis, and section continuity; engineering review required
Feeder scheduleCircuit quantity, load needs, protective-device functions, and future provisions
Interfaces and scopeCable entry, terminations, controls, upstream/downstream coordination, and approval owner
READY TO DISCUSS YOUR PROJECT?Let's build what's next.
Call (951) 403-5738
LET'S GET TO WORK

Power your next project
with confidence.

Talk through your switchgear and power distribution needs with our team.

Call (951) 403-5738
Request a Quote