Power distribution, with purpose.
Key interlocks can prevent selected switching sequences in medium-voltage metal-enclosed interrupter switchgear, but only when the sequence, trapped-key logic, and operating responsibilities are defined together. A useful plan starts with the states the system must allow or prohibit—not with a preferred lock or assumed standard arrangement. The example below is hypothetical; actual equipment, interlock functions, and operating procedures require project-specific engineering review and approval.
Map permitted states before specifying hardware
Describe each relevant device by its operating state and electrical or mechanical condition: for example, a source breaker open or closed, a tie switch open or closed, or an access door secured or released. Then identify which combinations are permissible. A state diagram or truth table makes the intended sequence reviewable and exposes gaps that prose alone can conceal. Distinguish a required prohibition from a preferred operating sequence; an interlock may block a particular action without proving that every other condition is safe.
Consider a hypothetical facility with two medium-voltage sources and a normally open bus tie. The design intent might permit either source to feed its assigned section, permit a transfer through the tie only after the appropriate source device is open, and prohibit unintended parallel operation. Those statements do not establish the actual switching sequence. Source grounding, protection scheme, transfer controls, utility rules, and equipment configuration can change what is permissible, so the project’s responsible engineers must define and approve the logic.
Assign keys, custody, and release conditions
For every key in the proposed sequence, document what holds it captive, the condition that releases it, where it must be used next, and how it returns to its original position. Identify who controls the key during normal operation and during maintenance or an abnormal event. If a key can be duplicated, shared, or removed from its intended chain, the design assumptions may no longer hold. Key ownership is an operational responsibility, not merely a hardware detail.
A sequence might require opening a source device before its key can be removed, then using that key to enable a tie operation. If access to a compartment is part of the sequence, define how the key is controlled while access is permitted and what condition restores it. Avoid relying on informal handoffs, memory, or labels as substitutes for the engineered sequence. Operating procedures should explain authorized actions and abnormal conditions, and must be approved by the owner and other responsible parties before use.

Supply inputs that determine the design
A quote request should identify the one-line diagram and switching philosophy, system nominal voltage, equipment maximum-voltage requirement, frequency, bus arrangement, source and tie devices, and relevant grounding method. Include available fault-current information and required short-circuit ratings for engineering review, while recognizing that system conditions and equipment ratings are separate values. Provide protection, control, and transfer schematics where available, plus compartment access requirements and any owner or utility operating rules that affect the proposed sequence.
Also state whether interlocks are required between devices within one lineup or across separate equipment, and identify existing equipment that may have to participate. Supply the desired key sequence or state diagram, the operating modes it must cover, and the parties who will review and approve it. If the logic is not yet settled, say so rather than treating an illustrative sequence as a final requirement. These inputs help identify design questions early; component availability and the manufacturable configuration must still be confirmed for the specific order.
Coordinate mechanical logic with electrical controls
Key interlocks address selected physical actions, while protection relays, electrical permissives, transfer controls, and operating procedures address other conditions. Define which function prevents each undesired state and where that function resides. Confirm interfaces among switchgear devices, remote control circuits, alarms, grounding provisions, and any upstream or downstream equipment. A key sequence that is mechanically consistent can still conflict with a control scheme or leave an operating condition unaddressed.
Discuss failure and maintenance cases during review. Examples include loss of control power, a device unavailable for operation, a key retained at an unexpected point in the sequence, or work that changes the normal source arrangement. These cases do not prescribe a universal response; they reveal assumptions the owner and engineer must resolve. Do not treat interlocking as a replacement for protection, lockout/tagout requirements, safe work practices, or approved operating procedures.
Balance simplicity, flexibility, and scope
A tightly constrained key chain can make an intended sequence clear, but may complicate maintenance, restoration, or operation under an approved alternate configuration. A more flexible arrangement may support additional modes while increasing the number of states that must be analyzed and the risk of ambiguous custody. Compare the operating modes the facility genuinely needs against the added devices, keys, documentation, and review effort. Avoid adding interlock functions without a defined hazard or operating purpose.
Set scope boundaries in the specification. State whether the requested work includes only interlock provisions in new switchgear or also control logic, field wiring, interfaces to existing devices, procedure development, and commissioning documentation. Identify who supplies final drawings, validates system conditions, approves the operating sequence, and accepts any field changes. A manufacturer can build to an agreed, feasible design; the owner’s designated engineering authority remains responsible for system requirements and approved operating practices.
Review the design and confirm order details
Before release, review the sequence against the one-line diagram and control documents, verify each key’s release and return conditions, and check that every required state is addressed. Resolve mismatches between drawings, specifications, and procedures before fabrication. For projects in Dallas–Fort Worth or elsewhere, clear document ownership and review gates are especially useful when the manufacturer, owner, engineer, utility, and operations team are in different locations. Do not infer a local manufacturing facility from service to a region.
A U.S. manufacturer can discuss custom new-equipment builds using American components and shorter lead time as a goal, subject to design and component availability. Confirm the proposed interlock hardware and interfaces for the specific order rather than assuming a standard arrangement is available. If the scope includes a low-voltage switchboard, UL 891 may be relevant to that assembly; it is not a general listing for medium-voltage switchgear. Equipment ratings, applicable standards, any U.S.-origin requirements, and approvals must be confirmed for the project.
Specifications & planning
Review the details that matter for your application. Final specifications and availability should be confirmed for your project.
| Evaluation factor | What to define |
|---|---|
| Permitted states | Device combinations allowed or prohibited; subject to engineering review |
| Key custody | Release condition, next use, return point, and responsible operator |
| System interfaces | Protection, controls, grounding, access, and connected equipment |
| Approval boundary | Design authority, procedure approval, document review, and field-change acceptance |
