Power distribution, with purpose.
A motor control center (MCC) and a switchboard can both distribute power, but they serve different operating needs. The MCC organizes motor-control units; the switchboard primarily distributes power through feeder circuits. Choosing between them—or specifying both—depends on the loads, operating methods, electrical design, and who owns each interface.
Start with the equipment’s job
An MCC groups motor-related control and protection equipment in a coordinated assembly. Depending on the specified design and confirmed component availability, its units may support functions such as motor starting, disconnecting, and control-circuit connections. The important question is not simply how many motors a facility has. It is whether operators need grouped motor controls, consistent unit arrangements, and a defined way to connect those units to the plant’s power and control systems.
A switchboard is generally selected to receive power and distribute it to downstream circuits through feeder devices. Those feeders may supply MCCs, panelboards, other distribution equipment, or facility loads, as the design requires. A switchboard is not a substitute for the motor-control functions provided by an MCC, just as an MCC should not be assumed to replace a project’s main distribution equipment. Confirm the required function, ratings, construction, and applicable standards for each assembly.
When a project may need both
A representative example is a facility with a main distribution point and several groups of motors. The switchboard could distribute power to an MCC feeder and to separate building or process feeders, while the MCC houses the specified control units for a set of motors. This is an illustrative arrangement, not a recommendation for a particular facility; a qualified project team must establish the one-line diagram, protection scheme, and equipment boundaries.
Using both types can make the division between broad distribution and grouped motor control easier to communicate, but it adds interfaces to engineer and document. The project must resolve feeder protection, available fault current, selective coordination objectives, grounding, control power, and physical connections. If the switchboard and MCC come from different suppliers, clarify who verifies compatibility across the boundary and who provides the required coordination information. Confirm product availability before treating a proposed arrangement as buildable.

Compare operating needs and tradeoffs
Consider how the equipment will be operated and maintained. An MCC may be appropriate when the design calls for multiple motor-control units grouped in an assembly, whereas a switchboard is centered on incoming and outgoing distribution circuits. Compare the required control methods, motor starting approach, unit configuration, feeder count, and access expectations. Specific features depend on the design and selected components; do not assume a particular unit type or control function is available until it is reviewed for the order.
Grouping can help align equipment organization with process areas or maintenance practices, but it also concentrates multiple functions in one assembly and can affect footprint, cable routing, and future expansion. A switchboard may provide a clearer distribution hierarchy, yet it still needs suitable downstream equipment for motor control where required. Cost and schedule comparisons should use the same project scope, ratings, and interfaces. Custom builds and shorter lead time are goals, not promises; component supply and engineering review affect feasibility and timing.
Define electrical and physical interfaces
Provide the nominal system voltage, frequency, grounding arrangement, source information, and available fault current at each connection point. Identify equipment maximum voltage rating separately from system nominal voltage, and state required continuous-current and short-circuit ratings for engineering review. The design team should also identify protective-device data and coordination objectives. Ratings, standards, and component availability must be confirmed for the specific order; a nominal voltage alone is not enough to establish suitability.
Document where the switchboard ends and the MCC begins: feeder device and termination responsibility, conductor or bus connection, neutral and grounding provisions, control wiring, communications, and any interlocks or status signals. Include the installation environment, enclosure requirements, access and working-space constraints, cable-entry preferences, and dimensional limits. These details help identify conflicts early, but final installation design and approval remain with the project’s responsible electrical professionals and authorities having jurisdiction.
Prepare a useful quote package
For a quote, supply the one-line diagram, load and motor schedule, sequence or control requirements, preferred equipment arrangement, and any existing project specifications. Include the source and downstream equipment context, target ratings, requested standards, drawings or interface documents, delivery destination, and required schedule. If the design is not settled, identify assumptions and open questions rather than presenting preliminary values as approved requirements. This allows the manufacturer to review scope and confirm what can be supplied.
For projects in Dallas–Fort Worth or elsewhere in the United States, delivery planning depends on the completed equipment scope and destination; service to a region does not establish a local manufacturing location. New custom equipment can be built using American components when confirmed for the order. Any U.S.-origin requirement needs a clear definition and verification, including how it applies to components. UL 891 applies to low-voltage switchboards, not generally to MCCs or medium-voltage equipment; confirm the applicable construction and standards for each assembly.
Keep design authority and approvals clear
The manufacturer can review the requested assembly scope, clarify interface information, and confirm product availability and order-specific details. That review does not replace the engineer of record’s responsibility for system design, calculations, protection coordination, code application, or approval of the complete installation. Likewise, a statement about one assembly’s construction should not be treated as approval of connected equipment or the overall electrical system.
Before release, reconcile the approved one-line diagram, schedules, drawings, and specifications for both equipment types. Resolve discrepancies in feeder names, ratings, protective devices, control interfaces, and connection responsibilities, then obtain the approvals required by the project. This disciplined handoff helps prevent a switchboard feeder from being specified without a compatible MCC interface—or motor-control units from being selected without a verified source and protection scheme.
Specifications & planning
Review the details that matter for your application. Final specifications and availability should be confirmed for your project.
| Evaluation factor | MCC consideration |
|---|---|
| Primary function | Grouped motor-control units |
| Typical interface | Receives a defined feeder; connects motor circuits |
| Key design inputs | Motor schedule and control requirements |
| Approval boundary | Confirm assembly scope and connected-system interface |
