NEW AMERICAN-MADE POWER DISTRIBUTIONSERVING DALLAS – FORT WORTH
Electrical equipment on a flatbed truck for transportation
NEW EQUIPMENT FOR DALLAS–FORT WORTH

13.8 kV Switchgear Specification Guide

Plan a 13.8 kV switchgear specification with clear system voltage, grounding, protection, insulation and service-interface requirements.

MADE IN USAAmerican components
UL 891Switchboard assemblies
SHORT LEAD TIMESConfirm your project schedule
BUILT FOR YOUR PROJECT

Power distribution, with purpose.

A 13.8 kV system is a nominal medium-voltage designation, not a complete equipment specification. Define how the source is grounded, what voltage the equipment must withstand, how protection coordinates with upstream and downstream devices, and which interfaces the switchgear must accommodate before requesting a quote. These details determine whether a proposed configuration suits the actual system; confirm that the specific arrangement and components are available before treating it as an offered product.

Define nominal voltage and phase relationships

In a typical three-phase system, 13.8 kV describes the nominal line-to-line voltage: the voltage measured between any two phase conductors. Line-to-neutral voltage applies only where a neutral reference is present and accessible. For a grounded-wye system with a neutral, the theoretical line-to-neutral value is about 7.97 kV, calculated by dividing 13.8 kV by the square root of three. That value does not mean every 13.8 kV installation provides a usable neutral, nor does it define the switchgear’s required insulation rating.

State the source and load arrangement, phase count, nominal frequency, and any neutral conductors or grounding transformers in the project documents. Identify whether the switchgear is connected to a utility service, generator, transformer secondary, or another source, and document any alternate-source operation. A voltage label by itself can conceal meaningful differences in grounding and operating conditions. For a Dallas–Fort Worth facility or a project elsewhere, the one-line diagram and utility or owner criteria should control the specification, not assumptions based on location.

Separate system voltage from equipment ratings

The system’s nominal 13.8 kV value describes its intended operating class; it is not automatically the equipment’s maximum rated voltage. Medium-voltage equipment is selected using its applicable rated-voltage class and insulation characteristics, including the withstand levels required for power-frequency and impulse events. These ratings must suit the system and applicable standards. Do not infer an equipment rating, certification, or compliance from the nominal system voltage alone.

Ask the engineer of record or equipment supplier to confirm the appropriate voltage class, insulation level, and ratings for the actual application. Include expected operating conditions, elevation where relevant to the design, environmental conditions, and any utility requirements that affect insulation selection. Record the source of each requirement in the specification so that switchgear, cables, terminations, instrument transformers, and connected transformers are evaluated as a coordinated system. Final ratings and standards requirements require project-specific review.

Illustrative close-up of copper busbars in a motor control panel
Illustrative industry photograph · ToT89 / Wikimedia Commons · resized · CC BY-SA 4.0

Specify grounding and fault behavior

Grounding method affects phase-to-ground voltage, ground-fault current, relay response, and the stress experienced by insulation during a fault. Common arrangements include solidly grounded, resistance-grounded, and impedance-grounded systems; an ungrounded system has different ground-fault behavior and operating considerations. The correct choice depends on the source design, continuity-of-service goals, protection philosophy, and owner or utility requirements. Do not leave the grounding method implicit in a 13.8 kV request.

Provide the grounding arrangement and, where applicable, grounding-resistor or grounding-transformer data, expected ground-fault current, and clearing-time assumptions. Identify whether residual, neutral, or other ground-fault sensing is required and how its signals reach the protective relay. The equipment design and relay settings must account for the actual grounding scheme rather than a generic fault-current value. An electrical engineer should verify the system study and protection approach before equipment ratings or settings are finalized.

Coordinate protection and interrupting duty

A switchgear specification should distinguish continuous-current requirements from short-circuit and interruption duties. Provide available fault current at the switchgear bus, the source X/R information when required for evaluation, and the intended clearing sequence. Fault duty can change with utility contributions, transformer impedance, parallel sources, and generator operation. A nominal 13.8 kV designation does not establish the required interrupting rating or short-time withstand capability.

Identify the protective devices and interfaces that must coordinate, including upstream relays or breakers, feeder protection, transformer protection, and downstream equipment. Supply relay functions, current-transformer ratios and accuracy needs, potential-transformer requirements, control power, trip and close circuits, and any communications or supervisory interfaces. Coordination and arc-flash studies may affect relay functions and settings, but do not replace equipment-duty verification. Confirm ratings and available components for the exact proposed configuration.

Match insulation, connections, and service interfaces

Document how incoming and outgoing circuits will connect: cable entry direction, conductor material and size, termination type, phase arrangement, and any bus or transition requirements. Include grounding-bus expectations, instrument-transformer locations, metering needs, and space or interface constraints that affect the lineup. Cable and termination insulation classes must be compatible with the system and equipment; a mismatch can undermine an otherwise suitable voltage selection.

Describe the installation environment and maintenance boundaries, including indoor or outdoor use, ambient conditions, available clearance, access routes, and the intended method for isolating equipment. Identify existing gear or transformers at each boundary and provide their nameplate data where available. These interfaces matter when replacing equipment or extending a lineup, because physical fit and electrical compatibility are separate questions. Any proposed design should be reviewed against the project drawings and applicable requirements before release.

Prepare a complete, reviewable quote request

For a useful quote request, provide the one-line diagram, equipment arrangement and feeder count, nominal voltage and frequency, grounding details, load and continuous-current requirements, available fault-current study, and protection and metering criteria. Include cable termination information, control schematics or interface requirements, environmental conditions, applicable standards, requested documentation, and delivery destination. Identify whether the scope is a new lineup or a specific replacement, and flag any dimensions or existing interfaces that cannot change.

The manufacturer builds and supplies new equipment, including custom configurations, and can work with American components where specified; component availability, U.S.-origin requirements, ratings, and standards must be confirmed for the particular order. A shorter lead time may be a goal, not a guaranteed schedule. Verify that the requested 13.8 kV configuration is actually offered before making a product assumption. A clear submittal package helps identify open engineering questions early and supports a more reliable scope and schedule review.

PROJECT CONSIDERATIONS

Specifications & planning

Review the details that matter for your application. Final specifications and availability should be confirmed for your project.

13.8 kV voltage planning: specifications and planning considerations
Evaluation factorWhat to document
Voltage basis13.8 kV nominal line-to-line; confirm phase and neutral arrangement
GroundingSystem method, grounding equipment, and expected ground-fault behavior
Equipment dutyRequired voltage class, insulation level, continuous current, and fault ratings
Protection and interfacesFault-study inputs, relay functions, terminations, controls, and connected equipment
READY TO DISCUSS YOUR PROJECT?Let's build what's next.
Call (951) 403-5738
LET'S GET TO WORK

Power your next project
with confidence.

Talk through your switchgear and power distribution needs with our team.

Call (951) 403-5738
Request a Quote