NEW AMERICAN-MADE POWER DISTRIBUTIONSERVING DALLAS – FORT WORTH
Installed electrical panels and conduit in an equipment room
NEW EQUIPMENT FOR DALLAS–FORT WORTH

15 kV Class Switchgear Specification Guide

Plan 15 kV class switchgear around system voltage, grounding, insulation, protection, and interfaces. Confirm project ratings and configuration before ordering.

MADE IN USAAmerican components
UL 891Switchboard assemblies
SHORT LEAD TIMESConfirm your project schedule
BUILT FOR YOUR PROJECT

Power distribution, with purpose.

“15 kV class” identifies an equipment voltage class; it does not mean the system operates at exactly 15 kV. A sound specification starts with the system’s nominal voltage and grounding arrangement, then checks the equipment’s rated voltage, insulation, interrupting duty, protection, and connected interfaces. Confirm that the manufacturer can supply the specific configuration before treating a 15 kV class assembly as an available product.

Separate the system’s nominal voltage from the equipment class

State the system nominal line-to-line voltage and the maximum voltage the equipment must accommodate. A nominal system voltage is an operating designation, while an equipment rating is a defined limit; the two values are related but are not interchangeable. The “15 kV class” label alone does not establish the assembly’s rated maximum voltage, insulation level, or ability to meet a particular utility or facility requirement.

For a quote, provide the one-line diagram and identify the source and load voltages, system frequency, and any planned transformer or bus transitions. Ask the manufacturer to confirm the equipment’s actual ratings for the proposed configuration. The particular 15 kV class arrangement may not be offered in every bus, compartment, protection, or interface combination, so verify capability before designing around a product assumption.

Document grounding and phase-to-ground conditions

Describe whether the system is solidly grounded, resistance grounded, reactance grounded, or ungrounded, and specify relevant grounding equipment such as a grounding transformer or resistor. These choices affect ground-fault current, relay sensing, fault duration, and the voltage that can appear from an unfaulted phase to ground. A voltage class by itself cannot establish suitable ground-fault protection or insulation coordination.

Line-to-line voltage is measured between phases; line-to-neutral voltage applies where a neutral is present and defined. On a three-phase grounded wye system, line-to-neutral voltage is ordinarily lower than line-to-line voltage, but the relationship should be confirmed from the actual system configuration. Provide winding connections, neutral grounding details, and the intended treatment of ground faults rather than inferring them from a nominal voltage label.

Illustrative close-up of copper busbars in a motor control panel
Illustrative industry photograph · ToT89 / Wikimedia Commons · resized · CC BY-SA 4.0

Coordinate rated voltage and insulation requirements

Specify the equipment maximum voltage and required insulation withstand levels, including the applicable power-frequency and impulse withstand criteria where required by the project. Insulation coordination depends on system exposure, grounding, surge protection, and connected equipment—not just the nominal voltage. Confirm that the proposed switchgear’s ratings and construction meet the project’s governing requirements for its location and duty.

Identify whether the installation is indoors or outdoors, the site altitude, ambient conditions, contamination concerns, and any unusual moisture or corrosion exposure. These conditions can affect insulation performance, clearances, enclosure selection, and component suitability. Confirm the exact standards and environmental requirements for the order; do not assume that a voltage-class designation or a general product description establishes compliance.

Match protection to available fault duty

Provide the available short-circuit current at the switchgear, the source impedance or utility fault information, and the required clearing time when known. The interrupting and withstand ratings must be evaluated for the actual system and proposed equipment configuration. A nominal voltage or 15 kV class label does not reveal whether a particular assembly can safely handle the site’s fault duty.

Describe the protection scheme and interfaces, including relay functions, current and voltage transformers, metering, trip power, and connections to upstream or downstream devices. Protection settings and coordination depend on the complete distribution system and the project engineer’s study. Confirm component availability and ratings for the specific order, and have qualified professionals review the design rather than relying on a generic class specification.

Plan frequency, interfaces, and service coordination

State the system frequency and identify all connected equipment whose ratings or operation depend on it. Include incoming and outgoing cable details, conductor arrangement, termination requirements, bus connections, grounding points, and any control or communications interfaces. Clear interface information reduces the risk of a physically buildable assembly that does not match the site’s electrical or installation requirements.

Coordinate the switchgear with transformers, generators, motors, transfer schemes, and downstream protective devices. Provide drawings, equipment data, operating sequences, and service constraints that affect access or compartment arrangement. For Dallas–Fort Worth projects, as for shipments elsewhere in the United States, confirm delivery constraints and site receiving requirements early; serving a region does not imply a local manufacturing facility or installation service.

Prepare a project-specific request for quotation

A useful request includes the one-line diagram, nominal and maximum system voltages, grounding method, frequency, fault-current data, insulation criteria, protection requirements, indoor or outdoor conditions, and required interfaces. Add preferred arrangement, cable entry and exit details, control power, metering needs, and applicable project or utility specifications. Identify which requirements are mandatory and which allow engineering alternatives.

The manufacturer builds and supplies new equipment, with custom builds and American components as options subject to confirmation for the specific order. Shorter lead time is a goal, not a guarantee; timing depends on the final design, component availability, and order requirements. Ask for confirmation of the actual 15 kV class configuration, ratings, standards, and any U.S.-origin requirements before release. All ratings and compliance details require project-specific review.

PROJECT CONSIDERATIONS

Specifications & planning

Review the details that matter for your application. Final specifications and availability should be confirmed for your project.

15 kV Class voltage planning: specifications and planning considerations
Evaluation factorInformation to establish
System voltageNominal line-to-line voltage and required equipment maximum voltage
GroundingGrounding method, neutral arrangement, and ground-fault expectations
Fault dutyAvailable short-circuit current and required interrupting or withstand criteria
Insulation and environmentRequired withstand levels, altitude, exposure, and applicable project standards
InterfacesFrequency, cable and bus connections, protection, controls, and service constraints
READY TO DISCUSS YOUR PROJECT?Let's build what's next.
Call (951) 403-5738
LET'S GET TO WORK

Power your next project
with confidence.

Talk through your switchgear and power distribution needs with our team.

Call (951) 403-5738
Request a Quote