NEW AMERICAN-MADE POWER DISTRIBUTIONSERVING DALLAS – FORT WORTH
Switchgear cabinets arranged on a warehouse floor
NEW EQUIPMENT FOR DALLAS–FORT WORTH

27 kV Switchgear Project Specifications

Specify 27 kV switchgear with clarity on nominal system voltage, equipment class, insulation, fault duty, interfaces, and quote-ready project data.

MADE IN USAAmerican components
UL 891Switchboard assemblies
SHORT LEAD TIMESConfirm your project schedule
BUILT FOR YOUR PROJECT

Power distribution, with purpose.

A “27 kV system” does not, by itself, identify the correct switchgear rating. Project specifications must distinguish the nominal voltage of the power system from the equipment’s maximum voltage rating and insulation capability. That distinction affects clearances, withstand requirements, connected equipment, and what a manufacturer can responsibly quote. For a custom new-equipment build, provide the project’s electrical basis and service conditions so the proposed configuration can be reviewed against the actual application.

Translate nominal voltage into an equipment class

Nominal system voltage describes the operating level assigned to the power system; an equipment voltage rating identifies the maximum system voltage for which the equipment is designed. In this context, 27 kV is normally a medium-voltage class, not a low-voltage switchboard rating. A specification that says only “27 kV switchgear” leaves open whether 27 kV is the nominal system voltage, a requested equipment class, or shorthand carried over from another document.

Before requesting a quote, state both the nominal voltage and the required maximum equipment voltage class, including the applicable project or utility criteria. Confirm that the class suits the system’s highest operating voltage and grounding arrangement. Do not infer that a particular voltage class is available or appropriate from its name alone; ratings and the proposed design must be confirmed for the specific order.

Specify insulation for the actual system conditions

Insulation coordination is more than selecting a voltage number. The specification should identify required power-frequency withstand and lightning-impulse withstand levels, as applicable, and the governing standards or utility requirements. These values describe how insulation is evaluated against different electrical stresses; they should not be guessed from nominal voltage or copied from a different equipment class without engineering review.

Describe conditions that can affect insulation selection and clearances, including installation altitude, indoor or outdoor service, contamination or moisture exposure, and unusual switching or transient concerns. Higher altitude can change required insulation clearances, while environmental exposure can influence enclosure and insulation-system decisions. When project conditions are not yet finalized, identify the assumption and ask that it be reviewed rather than treating a preliminary value as an approved design basis.

Illustrative close-up of copper busbars in a motor control panel
Illustrative industry photograph · ToT89 / Wikimedia Commons · resized · CC BY-SA 4.0

Separate insulation duty from short-circuit duty

Voltage class and insulation withstand do not establish the assembly’s short-circuit capability. Supply the available fault current at the switchgear location, the expected system configuration, and the protection-clearing assumptions used by the engineer. Also identify required momentary, interrupting, and short-time withstand duties where they apply. These are related but distinct selection criteria, and the correct requirement depends on the equipment design and switching devices.

Fault levels may change as transformers, utility sources, generators, or bus ties are added or rearranged. A rating that appears adequate for an early one-line drawing may not remain adequate after those changes. Ask the project engineer to confirm the governing fault study and duty at the equipment terminals. The manufacturer must confirm achievable ratings and component availability for the specific build; no generic 27 kV label guarantees a particular fault-duty rating.

Coordinate interfaces before freezing the lineup

A usable specification connects the switchgear to the rest of the system. Provide a current one-line diagram, source and feeder information, transformer data, grounding method, and the intended arrangement of main, feeder, and tie functions. Identify metering, protection, control power, communications, and any interlocking requirements. These details can affect compartment layout, instrument-transformer selection, wiring, and the interfaces needed by other project equipment.

Confirm cable entry direction, termination type, conductor information, phase arrangement, room constraints, and required access or maintenance clearances. If the 27 kV equipment connects to a transformer or another voltage class, document both sides of the interface rather than assuming the ratings match. Resolve scope boundaries early, including which devices and control components are required, so a quote does not depend on unstated assumptions.

Make standards and service conditions explicit

List the standards, editions, utility rules, and project specifications that govern the application, then identify any conflicts for engineering review. Standards and test requirements depend on equipment type and configuration; UL 891 applies to low-voltage switchboards and should not be presented as a general listing for 27 kV medium-voltage switchgear. State any required certification or listing specifically, and verify whether it applies to the proposed equipment rather than assuming it.

For a complete review, include frequency, continuous-current needs, ambient conditions, indoor or outdoor location, seismic or other site criteria where applicable, and required enclosure details. State any U.S.-origin or domestic-content requirements and their governing definitions. American components may be considered in a custom build, but component origin and compliance with procurement rules must be confirmed for the particular order.

Prepare a quote-ready project package

A useful request for quotation includes the nominal system voltage and required equipment voltage class, insulation withstand requirements, one-line diagram, fault-study data, device and protection schedules, cable and termination details, and the applicable standards. Add the service environment, site constraints, delivery destination, project milestones, and any required submittal or documentation format. Identify which values are firm and which remain provisional so review can focus on the open decisions.

A manufacturer can use that information to develop a custom new-equipment proposal and check component availability, ratings, interfaces, and standards against the project. Shorter lead time can be a goal, but schedule depends on the approved design, components, and order-specific requirements and is not guaranteed by the 27 kV designation. For projects in Dallas–Fort Worth or elsewhere nationwide, provide the delivery destination and receiving constraints with the request; confirm final ratings, origin requirements, and schedule before order release.

PROJECT CONSIDERATIONS

Specifications & planning

Review the details that matter for your application. Final specifications and availability should be confirmed for your project.

27 kV switchgear: specifications and planning considerations
Evaluation factorInformation to define
Voltage basisNominal system voltage and required maximum equipment voltage class
InsulationWithstand requirements, altitude, and environmental conditions
Fault dutyAvailable fault current and applicable interrupting and withstand duties
InterfacesOne-line, connections, cable details, protection, controls, and standards
READY TO DISCUSS YOUR PROJECT?Let's build what's next.
Call (951) 403-5738
LET'S GET TO WORK

Power your next project
with confidence.

Talk through your switchgear and power distribution needs with our team.

Call (951) 403-5738
Request a Quote